Eaton HCM1A1307V2-5R6-R 5.6 uH AEC-Q200 Inductor, 12 A
Eaton HCM1A1307V2-5R6-R 5.6 uH AEC-Q200 Inductor, 12 A

Eaton HCM1A1307V2-5R6-R 5.6 uH AEC-Q200 Inductor, 12 A

Share
Eaton HCM1A1307V2-5R6-R: AEC-Q200 automotive power inductor, 5.6 uH ±20%, 12 A Irms, Isat 18 A, DCR 7.21 mOhm, 13.8 x 12.9 mm.
    • Product Details
    • Download

    Eaton HCM1A1307V2-5R6-R 5.6 uH AEC-Q200 Inductor, 12 A

    HCM1A1307V2-5R6-R at a glance: AEC-Q200 automotive power inductor, 5.6 uH ±20%, 12 A Irms, Isat 18 A (20% rolloff @ +25 °C), DCR 7.21 mOhm, 13.8 x 12.9 mm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberHCM1A1307V2-5R6-R
    OCL (open circuit inductance)5.6 uH ±20%
    FLL minimum, at Isat3.58 uH
    Irms (DC, 40 °C rise)12 A
    Isat (20% rolloff @ +25 °C)18 A
    DCR typical @ +20 °C7.21 mOhm
    DCR maximum @ +20 °C8.3 mOhm
    SRF typical11 MHz
    K-factor (Bp-p = K x L x dI)64, Bp-p in Gauss
    Package13.8 x 12.9 mm
    Height6.5 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10905

    Dimensions and Pad Layout

    HCM1A1307V2-5R6-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10905: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    How to Read These Ratings

    This is the automotive version of the molded high-current inductor. The body is a molded powder core, the winding is shielded by the magnetic material itself, and the operating range runs to +155 °C. It is the part that goes on the DC-DC stages of body electronics, ADAS modules and infotainment head units.

    With 7.21 mOhm typical, the I-squared-R loss at the full 12 A rating is about 1.04 W. Compare that against the converter output power before deciding whether the part needs airflow or a copper pour under it.

    Saturation is quoted as 20% rolloff @ +25 °C. At that point the inductance has fallen to the stated fraction of its nominal value – the part is not damaged there, it simply stops behaving like the inductance on the label. Design the peak current to stay inside that boundary with margin for tolerance.

    At Isat the part holds about 907 uJ. On a multiphase rail that is the energy per phase available to bridge a load step, which sets how much bulk capacitance the controller still needs.

    The K-factor of 64 converts inductance and ripple into flux swing: each amp of peak-to-peak ripple moves the core through about 358 Gauss of Bp-p, the figure the core-loss curve is plotted against.

    Self-resonant frequency is 11 MHz typical. Above that the part becomes capacitive and stops behaving as an inductor, which is why the switching frequency and its first harmonics should stay well below it.

    Series Positioning

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    Of the 20 values listed for HCM1A1307V2, this is the 11th, in a family covering 0.22 uH to 56 uH.

    One step down the table, HCM1A1307V2-4R7-R, sits at 4.7 uH with 13 A and 6.25 mOhm – the lower inductance buys about 3 A of extra current in the same body.

    • Core material: alloy powder core, 13.8 x 12.9 mm body at 6.5 mm.
    • Typical applications: body electronics; central body control module; headlamps, tail lamps and interior lighting and led lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control; advanced driver assistance systems.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Sizing It Into a Design

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 8.3 mOhm becomes roughly 12.7 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Check Isat and DCR at the hot corner, not at +20 °C.
    • Verify the qualification and the mounting process match the assembly line.
    • Confirm the qualification file covers the module-level test plan.

    Frequently Asked Questions

    Why do V2 and V3 parts exist?
    They are later revisions of the same body size with a changed electrical row – typically a higher current rating or an extra parameter such as self-resonant frequency. They are separate orderable parts, not substitutes.

    What is the self-resonant frequency used for?
    It marks the point where the winding capacitance dominates. Keep the switching frequency and the harmonics that carry energy below it, and use it to compare candidates of the same inductance.

    Why do V2 and V3 parts exist?
    They are later revisions of the same body size with a changed electrical row – typically a higher current rating or an extra parameter such as self-resonant frequency. They are separate orderable parts, not substitutes.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products