Eaton HCM1A1307V2-6R8-R 6.8 uH Shielded Automotive Inductor
Eaton HCM1A1307V2-6R8-R 6.8 uH Shielded Automotive Inductor

Eaton HCM1A1307V2-6R8-R 6.8 uH Shielded Automotive Inductor

Share
Eaton HCM1A1307V2-6R8-R: AEC-Q200 automotive power inductor, 6.8 uH ±20%, 10 A Irms, Isat 15 A, DCR 9.5 mOhm, 13.8 x 12.9 mm.
    • Product Details
    • Download

    Eaton HCM1A1307V2-6R8-R 6.8 uH Shielded Automotive Inductor

    HCM1A1307V2-6R8-R at a glance: AEC-Q200 automotive power inductor, 6.8 uH ±20%, 10 A Irms, Isat 15 A (20% rolloff @ +25 °C), DCR 9.5 mOhm, 13.8 x 12.9 mm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberHCM1A1307V2-6R8-R
    OCL (open circuit inductance)6.8 uH ±20%
    FLL minimum, at Isat4.35 uH
    Irms (DC, 40 °C rise)10 A
    Isat (20% rolloff @ +25 °C)15 A
    DCR typical @ +20 °C9.5 mOhm
    DCR maximum @ +20 °C11.5 mOhm
    SRF typical9 MHz
    K-factor (Bp-p = K x L x dI)52, Bp-p in Gauss
    Package13.8 x 12.9 mm
    Height6.5 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10905

    Mechanical Dimensions & Pad Layout

    HCM1A1307V2-6R8-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10905: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    How to Read These Ratings

    This is the automotive version of the molded high-current inductor. The body is a molded powder core, the winding is shielded by the magnetic material itself, and the operating range runs to +155 °C. It is the part that goes on the DC-DC stages of body electronics, ADAS modules and infotainment head units.

    With 9.5 mOhm typical, the I-squared-R loss at the full 10 A rating is about 0.95 W. Compare that against the converter output power before deciding whether the part needs airflow or a copper pour under it.

    The Isat column is 20% rolloff @ +25 °C. Note what it does and does not mean: it is a defined rolloff point, not a destruction limit. Above it the inductance continues to fall, which is why the transient peak current should be checked against the curve, not just against the number.

    The core stores roughly 765 uJ at the saturation point – a useful figure when sizing the output capacitance that has to absorb the same transient.

    K-factor 52 means the flux swing is about 354 Gauss per amp of ripple. Core loss scales with the flux amplitude and the frequency, so this is the number to carry into the loss calculation rather than the inductance alone.

    Self-resonant frequency is 9 MHz typical. Above that the part becomes capacitive and stops behaving as an inductor, which is why the switching frequency and its first harmonics should stay well below it.

    Positioning in the Range

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    In the HCM1A1307V2 line-up this part is number 12 of 20 by inductance, between 0.22 uH and 56 uH.

    Compared with its neighbours in the table, HCM1A1307V2-7R8-R trades 2 A of rated current for the next inductance step, which is the usual compromise in this family.

    • Core material: alloy powder core, 13.8 x 12.9 mm body at 6.5 mm.
    • Typical applications: body electronics; central body control module; headlamps, tail lamps and interior lighting and led lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control; advanced driver assistance systems.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Putting It to Work

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 11.5 mOhm becomes roughly 17.6 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Verify the part marking for revision traceability in production.
    • Check Isat and DCR at the hot corner, not at +20 °C.
    • Check Isat and DCR at the hot corner, not at +20 °C.

    Frequently Asked Questions

    What is the self-resonant frequency used for?
    It marks the point where the winding capacitance dominates. Keep the switching frequency and the harmonics that carry energy below it, and use it to compare candidates of the same inductance.

    Is the part shielded for ADAS modules?
    The molded powder core encloses the winding, so the radiated field is small. That is why the family is used next to sensor front ends and camera interfaces.

    Does the automotive grade change the electrical values?
    Not by itself, but it changes the qualification and often the temperature range. Compare the rows of the automotive data sheet against the commercial one rather than assuming they match.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message