Eaton HCM1A1307V3-560-R 56 uH Shielded Automotive Inductor
Eaton HCM1A1307V3-560-R 56 uH Shielded Automotive Inductor

Eaton HCM1A1307V3-560-R 56 uH Shielded Automotive Inductor

Share
Eaton HCM1A1307V3-560-R: AEC-Q200 automotive power inductor, 56 uH ±20%, 4 A Irms, Isat 4.3 A, DCR 55 mOhm, 13.8 x 12.9 mm.
    • Product Details
    • Download

    Eaton HCM1A1307V3-560-R 56 uH Shielded Automotive Inductor

    HCM1A1307V3-560-R at a glance: AEC-Q200 automotive power inductor, 56 uH ±20%, 4 A Irms, Isat 4.3 A (20% rolloff @ +25 °C), DCR 55 mOhm, 13.8 x 12.9 mm.

    Specification Table

    ParameterValue
    Orderable part numberHCM1A1307V3-560-R
    OCL (open circuit inductance)56 uH ±20%
    FLL minimum, at Isat35.8 uH
    Irms (DC, 40 °C rise)4 A
    Isat (20% rolloff @ +25 °C)4.3 A
    DCR typical @ +20 °C55 mOhm
    DCR maximum @ +20 °C65 mOhm
    SRF typical3 MHz
    K-factor (Bp-p = K x L x dI)54, Bp-p in Gauss
    Package13.8 x 12.9 mm
    Height6.5 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data ELX1489

    Dimensions and Pad Layout

    HCM1A1307V3-560-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data ELX1489: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    The Figures Explained

    Automotive power rails ask for two things a commercial inductor does not always give: a qualified construction and a saturation curve that is still usable at the hot corner. The molded powder core here provides both, with AEC-Q200 qualification and a soft rolloff that keeps inductance present at transient peak current.

    With 55 mOhm typical, the I-squared-R loss at the full 4 A rating is about 0.88 W. Compare that against the converter output power before deciding whether the part needs airflow or a copper pour under it.

    The saturation rating reads 20% rolloff @ +25 °C. Treat it as the edge of the linear region: below it the inductance is within tolerance, above it the value droops. For a current-mode converter that means the peak current at the worst-case load step is what must fit under this number.

    Energy storage at the saturation current is around 518 uJ, the number that connects the inductance and the current rating into a single transient figure.

    The K-factor of 54 converts inductance and ripple into flux swing: each amp of peak-to-peak ripple moves the core through about 3,024 Gauss of Bp-p, the figure the core-loss curve is plotted against.

    Self-resonant frequency is 3 MHz typical. Above that the part becomes capacitive and stops behaving as an inductor, which is why the switching frequency and its first harmonics should stay well below it.

    Positioning in the Range

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    The HCM1A1307V3 family spans 0.22 uH to 56 uH; this row sits at position 20 of 20.

    Compared with its neighbours in the table, HCM1A1307V3-330-R trades 0 A of rated current for the next inductance step, which is the usual compromise in this family.

    • Core material: alloy powder core, 13.8 x 12.9 mm body at 6.5 mm.
    • Typical applications: body electronics; central body control module; headlamps, tail lamps and interior lighting and led lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control; advanced driver assistance systems.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Sizing and Layout Notes

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 65 mOhm becomes roughly 99.5 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Verify the qualification and the mounting process match the assembly line.
    • Verify the part marking for revision traceability in production.
    • Check Isat and DCR at the hot corner, not at +20 °C.

    Frequently Asked Questions

    What is the self-resonant frequency used for?
    It marks the point where the winding capacitance dominates. Keep the switching frequency and the harmonics that carry energy below it, and use it to compare candidates of the same inductance.

    Why do V2 and V3 parts exist?
    They are later revisions of the same body size with a changed electrical row – typically a higher current rating or an extra parameter such as self-resonant frequency. They are separate orderable parts, not substitutes.

    Why do V2 and V3 parts exist?
    They are later revisions of the same body size with a changed electrical row – typically a higher current rating or an extra parameter such as self-resonant frequency. They are separate orderable parts, not substitutes.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products