Eaton HCM1A1707-3R3-R 3.3 uH AEC-Q200 Inductor, 21 A
Eaton HCM1A1707-3R3-R 3.3 uH AEC-Q200 Inductor, 21 A

Eaton HCM1A1707-3R3-R 3.3 uH AEC-Q200 Inductor, 21 A

Share
Eaton HCM1A1707-3R3-R: AEC-Q200 automotive power inductor, 3.3 uH ±20%, 21 A Irms, Isat 22 A, DCR 3.1 mOhm, 17.5 x 17.2 mm.
    • Product Details
    • Download

    Eaton HCM1A1707-3R3-R 3.3 uH AEC-Q200 Inductor, 21 A

    HCM1A1707-3R3-R at a glance: AEC-Q200 automotive power inductor, 3.3 uH ±20%, 21 A Irms, Isat 22 A (20% rolloff @ +25 °C), DCR 3.1 mOhm, 17.5 x 17.2 mm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberHCM1A1707-3R3-R
    OCL (open circuit inductance)3.3 uH ±20%
    FLL minimum, at Isat2.11 uH
    Irms (DC, 40 °C rise)21 A
    Isat (20% rolloff @ +25 °C)22 A
    DCR typical @ +20 °C3.1 mOhm
    DCR maximum @ +20 °C3.4 mOhm
    K-factor (Bp-p = K x L x dI)103, Bp-p in Gauss
    Package17.5 x 17.2 mm
    Height7.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10553

    Mechanical Drawing

    HCM1A1707-3R3-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10553: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    What the Numbers Mean

    AEC-Q200 qualified, molded, magnetically shielded, and rated to +155 °C ambient plus self-heating. The automotive grading is not a label on a commercial part: the test regime covers thermal shock, vibration and moisture, and the data sheet quotes the parameters at the temperature extremes the qualification demands.

    At the rated 21 A the winding dissipates about 1.37 W in copper alone, using the typical DCR of 3.1 mOhm. That figure is the floor of the loss budget: it assumes the current is pure DC, and any ripple adds to it.

    The saturation rating reads 20% rolloff @ +25 °C. Treat it as the edge of the linear region: below it the inductance is within tolerance, above it the value droops. For a current-mode converter that means the peak current at the worst-case load step is what must fit under this number.

    Stored energy at Isat is about 799 uJ, which is the energy the inductor hands to the load during a transient before the control loop reacts.

    K-factor 103 means the flux swing is about 340 Gauss per amp of ripple. Core loss scales with the flux amplitude and the frequency, so this is the number to carry into the loss calculation rather than the inductance alone.

    What This Family Is For

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    Within the HCM1A1707 family this is value 4 of 13, in a range that runs from 1 uH to 68 uH.

    One step down the table, HCM1A1707-2R2-R, sits at 2.2 uH with 24 A and 2.4 mOhm – the lower inductance buys about 6 A of extra current in the same body.

    • Core material: alloy powder core, 17.5 x 17.2 mm body at 7.0 mm.
    • Typical applications: body electronics; central body control module; headlamps, tail lamps and interior lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control; advanced driver assistance systems.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Design Notes

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 3.4 mOhm becomes roughly 5.2 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Verify the qualification and the mounting process match the assembly line.
    • Verify the part marking for revision traceability in production.
    • Check the hot-corner saturation margin against the worst-case load step.

    Frequently Asked Questions

    What is the self-resonant frequency used for?
    It marks the point where the winding capacitance dominates. Keep the switching frequency and the harmonics that carry energy below it, and use it to compare candidates of the same inductance.

    Does the automotive grade change the electrical values?
    Not by itself, but it changes the qualification and often the temperature range. Compare the rows of the automotive data sheet against the commercial one rather than assuming they match.

    Does the automotive grade change the electrical values?
    Not by itself, but it changes the qualification and often the temperature range. Compare the rows of the automotive data sheet against the commercial one rather than assuming they match.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products