Eaton HCM1A1707-680-R 68 uH Shielded Automotive Inductor
Eaton HCM1A1707-680-R 68 uH Shielded Automotive Inductor

Eaton HCM1A1707-680-R 68 uH Shielded Automotive Inductor

Share
Eaton HCM1A1707-680-R: AEC-Q200 automotive power inductor, 68 uH ±20%, 5.2 A Irms, Isat 6 A, DCR 51 mOhm, 17.5 x 17.2 mm.
    • Product Details
    • Download

    Eaton HCM1A1707-680-R 68 uH Shielded Automotive Inductor

    HCM1A1707-680-R at a glance: AEC-Q200 automotive power inductor, 68 uH ±20%, 5.2 A Irms, Isat 6 A (20% rolloff @ +25 °C), DCR 51 mOhm, 17.5 x 17.2 mm.

    Specification Table

    ParameterValue
    Orderable part numberHCM1A1707-680-R
    OCL (open circuit inductance)68 uH ±20%
    FLL minimum, at Isat43.5 uH
    Irms (DC, 40 °C rise)5.2 A
    Isat (20% rolloff @ +25 °C)6 A
    DCR typical @ +20 °C51 mOhm
    DCR maximum @ +20 °C60 mOhm
    K-factor (Bp-p = K x L x dI)17, Bp-p in Gauss
    Package17.5 x 17.2 mm
    Height7.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10553

    Dimensions and Pad Layout

    HCM1A1707-680-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10553: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    The Figures Explained

    Molded, shielded, AEC-Q200: the family is built for under-hood and in-cabin electronics where the ambient can reach 125 °C and the board cannot afford a radiating inductor. Soft saturation means the transient current does not disappear the inductance, and the shielding keeps the switching harmonics off nearby sensor wiring.

    With 51 mOhm typical, the I-squared-R loss at the full 5.2 A rating is about 1.38 W. Compare that against the converter output power before deciding whether the part needs airflow or a copper pour under it.

    Saturation is quoted as 20% rolloff @ +25 °C. At that point the inductance has fallen to the stated fraction of its nominal value – the part is not damaged there, it simply stops behaving like the inductance on the label. Design the peak current to stay inside that boundary with margin for tolerance.

    At Isat the part holds about 1,224 uJ. On a multiphase rail that is the energy per phase available to bridge a load step, which sets how much bulk capacitance the controller still needs.

    K-factor 17 means the flux swing is about 1,156 Gauss per amp of ripple. Core loss scales with the flux amplitude and the frequency, so this is the number to carry into the loss calculation rather than the inductance alone.

    Series Positioning

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    Within the HCM1A1707 family this is value 13 of 13, in a range that runs from 1 uH to 68 uH.

    The next value up in the same family, HCM1A1707-470-R, gives 47 uH at 5.5 A and DCR 41 mOhm: the extra inductance costs about 0 A of rated current.

    • Core material: alloy powder core, 17.5 x 17.2 mm body at 7.0 mm.
    • Typical applications: body electronics; central body control module; headlamps, tail lamps and interior lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control; advanced driver assistance systems.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Sizing It Into a Design

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 60 mOhm becomes roughly 91.8 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Confirm the qualification file covers the module-level test plan.
    • Confirm the revision letter (base / V2 / V3) before comparing electrical rows.
    • Confirm the revision letter (base / V2 / V3) before comparing electrical rows.

    Frequently Asked Questions

    Is the part shielded for ADAS modules?
    The molded powder core encloses the winding, so the radiated field is small. That is why the family is used next to sensor front ends and camera interfaces.

    Is the part shielded for ADAS modules?
    The molded powder core encloses the winding, so the radiated field is small. That is why the family is used next to sensor front ends and camera interfaces.

    What is the self-resonant frequency used for?
    It marks the point where the winding capacitance dominates. Keep the switching frequency and the harmonics that carry energy below it, and use it to compare candidates of the same inductance.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products