Eaton HCM1A1707-6R8-R AEC-Q200 Inductor 6.8 uH, Isat 18 A
Eaton HCM1A1707-6R8-R AEC-Q200 Inductor 6.8 uH, Isat 18 A

Eaton HCM1A1707-6R8-R AEC-Q200 Inductor 6.8 uH, Isat 18 A

Share
Eaton HCM1A1707-6R8-R: AEC-Q200 automotive power inductor, 6.8 uH ±20%, 12 A Irms, Isat 18 A, DCR 6.55 mOhm, 17.5 x 17.2 mm.
    • Product Details
    • Download

    Eaton HCM1A1707-6R8-R AEC-Q200 Inductor 6.8 uH, Isat 18 A

    HCM1A1707-6R8-R at a glance: AEC-Q200 automotive power inductor, 6.8 uH ±20%, 12 A Irms, Isat 18 A (20% rolloff @ +25 °C), DCR 6.55 mOhm, 17.5 x 17.2 mm.

    Specification Table

    ParameterValue
    Orderable part numberHCM1A1707-6R8-R
    OCL (open circuit inductance)6.8 uH ±20%
    FLL minimum, at Isat4.35 uH
    Irms (DC, 40 °C rise)12 A
    Isat (20% rolloff @ +25 °C)18 A
    DCR typical @ +20 °C6.55 mOhm
    DCR maximum @ +20 °C7.55 mOhm
    K-factor (Bp-p = K x L x dI)79, Bp-p in Gauss
    Package17.5 x 17.2 mm
    Height7.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10553

    Mechanical Drawing

    HCM1A1707-6R8-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10553: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    How to Read These Ratings

    This is the automotive version of the molded high-current inductor. The body is a molded powder core, the winding is shielded by the magnetic material itself, and the operating range runs to +155 °C. It is the part that goes on the DC-DC stages of body electronics, ADAS modules and infotainment head units.

    Copper loss at the rated current works out to roughly 0.943 W from a typical DCR of 6.55 mOhm at 12 A. It is the number to start a thermal stack-up with, before core loss and before AC resistance rise.

    The Isat column is 20% rolloff @ +25 °C. Note what it does and does not mean: it is a defined rolloff point, not a destruction limit. Above it the inductance continues to fall, which is why the transient peak current should be checked against the curve, not just against the number.

    The core stores roughly 1,102 uJ at the saturation point – a useful figure when sizing the output capacitance that has to absorb the same transient.

    With K = 79, a peak-to-peak ripple of one amp produces roughly 537 Gauss of flux swing. Read the core-loss graph at that amplitude and at the switching frequency to get the core contribution to the total loss.

    What This Family Is For

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    The HCM1A1707 family spans 1 uH to 68 uH; this row sits at position 6 of 13.

    One step down the table, HCM1A1707-4R7-R, sits at 4.7 uH with 18 A and 4.4 mOhm – the lower inductance buys about 6 A of extra current in the same body.

    • Core material: alloy powder core, 17.5 x 17.2 mm body at 7.0 mm.
    • Typical applications: body electronics; central body control module; headlamps, tail lamps and interior lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control; advanced driver assistance systems.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Putting It to Work

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 7.55 mOhm becomes roughly 11.6 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Check the hot-corner saturation margin against the worst-case load step.
    • Verify the qualification and the mounting process match the assembly line.
    • Check Isat and DCR at the hot corner, not at +20 °C.

    Frequently Asked Questions

    What is the self-resonant frequency used for?
    It marks the point where the winding capacitance dominates. Keep the switching frequency and the harmonics that carry energy below it, and use it to compare candidates of the same inductance.

    What does AEC-Q200 cover?
    The qualification regime for passive components in automotive use: thermal shock, temperature cycling, vibration, mechanical shock, moisture resistance and solderability, among others. It qualifies the construction, not the board design.

    What is the operating temperature range?
    The rated range is quoted as ambient plus self-temperature rise, up to the maximum shown in the table. The part is qualified across that span, but the hot corner is where saturation and DCR must be checked.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message