Eaton HCM1A1707V2-2R2-R AEC-Q200 Inductor 2.2 uH, Isat 31 A
Eaton HCM1A1707V2-2R2-R AEC-Q200 Inductor 2.2 uH, Isat 31 A

Eaton HCM1A1707V2-2R2-R AEC-Q200 Inductor 2.2 uH, Isat 31 A

Share
Eaton HCM1A1707V2-2R2-R: AEC-Q200 automotive power inductor, 2.2 uH ±20%, 22 A Irms, Isat 31 A, DCR 2.25 mOhm, 17.45 x 17.15 mm.
    • Product Details
    • Download

    Eaton HCM1A1707V2-2R2-R AEC-Q200 Inductor 2.2 uH, Isat 31 A

    HCM1A1707V2-2R2-R at a glance: AEC-Q200 automotive power inductor, 2.2 uH ±20%, 22 A Irms, Isat 31 A (20% rolloff @ +25 °C), DCR 2.25 mOhm, 17.45 x 17.15 mm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberHCM1A1707V2-2R2-R
    OCL (open circuit inductance)2.2 uH ±20%
    FLL minimum, at Isat1.41 uH
    Irms (DC, 40 °C rise)22 A
    Isat (20% rolloff @ +25 °C)31 A
    DCR typical @ +20 °C2.25 mOhm
    DCR maximum @ +20 °C2.41 mOhm
    SRF typical18 MHz
    K-factor (Bp-p = K x L x dI)82, Bp-p in Gauss
    Package17.45 x 17.15 mm
    Height7.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10906

    Mechanical Drawing

    HCM1A1707V2-2R2-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10906: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    Reading the Data Sheet

    Molded, shielded, AEC-Q200: the family is built for under-hood and in-cabin electronics where the ambient can reach 125 °C and the board cannot afford a radiating inductor. Soft saturation means the transient current does not disappear the inductance, and the shielding keeps the switching harmonics off nearby sensor wiring.

    The DCR figure of 2.25 mOhm is what sets the efficiency: at 22 A the winding drops about 0.049 mV and dissipates 1.09 W. On a low-voltage rail that drop is a measurable fraction of the output, so the DCR column deserves as much attention as the inductance.

    Isat is specified as 20% rolloff @ +25 °C, so the number is a rolloff criterion rather than an absolute maximum. The useful working range extends a little beyond it on a soft saturation core, but the loop compensation has to be designed for the inductance that remains.

    The core stores roughly 1,057 uJ at the saturation point – a useful figure when sizing the output capacitance that has to absorb the same transient.

    With K = 82, a peak-to-peak ripple of one amp produces roughly 180 Gauss of flux swing. Read the core-loss graph at that amplitude and at the switching frequency to get the core contribution to the total loss.

    Self-resonant frequency is 18 MHz typical. Above that the part becomes capacitive and stops behaving as an inductor, which is why the switching frequency and its first harmonics should stay well below it.

    Series Positioning

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    Of the 13 values listed for HCM1A1707V2, this is the 3th, in a family covering 1 uH to 68 uH.

    The next value up in the same family, HCM1A1707V2-3R3-R, gives 3.3 uH at 19.5 A and DCR 3 mOhm: the extra inductance costs about 3.5 A of rated current.

    • Core material: alloy powder core, 17.45 x 17.15 mm body at 7.0 mm.
    • Typical applications: body electronics; central body control module; headlamps, tail lamps and interior lighting and led lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control; advanced driver assistance systems.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Sizing and Layout Notes

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 2.41 mOhm becomes roughly 3.69 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Confirm the revision letter (base / V2 / V3) before comparing electrical rows.
    • Check Isat and DCR at the hot corner, not at +20 °C.
    • Confirm the revision letter (base / V2 / V3) before comparing electrical rows.

    Frequently Asked Questions

    Why do V2 and V3 parts exist?
    They are later revisions of the same body size with a changed electrical row – typically a higher current rating or an extra parameter such as self-resonant frequency. They are separate orderable parts, not substitutes.

    Is the part shielded for ADAS modules?
    The molded powder core encloses the winding, so the radiated field is small. That is why the family is used next to sensor front ends and camera interfaces.

    What is the operating temperature range?
    The rated range is quoted as ambient plus self-temperature rise, up to the maximum shown in the table. The part is qualified across that span, but the hot corner is where saturation and DCR must be checked.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products