Eaton HCM1A2213V2-101-R 100 uH Automotive Power Inductor
Eaton HCM1A2213V2-101-R 100 uH Automotive Power Inductor

Eaton HCM1A2213V2-101-R 100 uH Automotive Power Inductor

Share
Eaton HCM1A2213V2-101-R: AEC-Q200 automotive power inductor, 100 uH ±20%, 6.4 A Irms, Isat 8 A, DCR 36 mOhm, 22.78 x 22.3 mm.
    • Product Details
    • Download

    Eaton HCM1A2213V2-101-R 100 uH Automotive Power Inductor

    HCM1A2213V2-101-R at a glance: AEC-Q200 automotive power inductor, 100 uH ±20%, 6.4 A Irms, Isat 8 A (20% rolloff @ +25 °C), DCR 36 mOhm, 22.78 x 22.3 mm.

    Key Specifications

    ParameterValue
    Orderable part numberHCM1A2213V2-101-R
    OCL (open circuit inductance)100 uH ±20%
    FLL minimum, at Isat64 uH
    Irms (DC, 40 °C rise)6.4 A
    Isat (20% rolloff @ +25 °C)8 A
    DCR typical @ +20 °C36 mOhm
    DCR maximum @ +20 °C39.5 mOhm
    SRF typical1.9 MHz
    K-factor (Bp-p = K x L x dI)5, Bp-p in Gauss
    Package22.78 x 22.3 mm
    Height13.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10907

    Outline Drawing

    HCM1A2213V2-101-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10907: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    Reading the Data Sheet

    Automotive power rails ask for two things a commercial inductor does not always give: a qualified construction and a saturation curve that is still usable at the hot corner. The molded powder core here provides both, with AEC-Q200 qualification and a soft rolloff that keeps inductance present at transient peak current.

    At the rated 6.4 A the winding dissipates about 1.48 W in copper alone, using the typical DCR of 36 mOhm. That figure is the floor of the loss budget: it assumes the current is pure DC, and any ripple adds to it.

    Isat is specified as 20% rolloff @ +25 °C, so the number is a rolloff criterion rather than an absolute maximum. The useful working range extends a little beyond it on a soft saturation core, but the loop compensation has to be designed for the inductance that remains.

    Energy storage at the saturation current is around 3,200 uJ, the number that connects the inductance and the current rating into a single transient figure.

    The K-factor of 5 converts inductance and ripple into flux swing: each amp of peak-to-peak ripple moves the core through about 500 Gauss of Bp-p, the figure the core-loss curve is plotted against.

    Self-resonant frequency is 1.9 MHz typical. Above that the part becomes capacitive and stops behaving as an inductor, which is why the switching frequency and its first harmonics should stay well below it.

    Where This Series Fits

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    The HCM1A2213V2 family spans 0.47 uH to 100 uH; this row sits at position 14 of 14.

    The next value up in the same family, HCM1A2213V2-820-R, gives 82 uH at 7 A and DCR 29.9 mOhm: the extra inductance costs about 0 A of rated current.

    • Core material: alloy powder core, 22.78 x 22.3 mm body at 13.0 mm.
    • Typical applications: body electronics; central body control module; headlamps, tail lamps and interior lighting and led lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control; advanced driver assistance systems.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Sizing and Layout Notes

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 39.5 mOhm becomes roughly 60.5 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Check Isat and DCR at the hot corner, not at +20 °C.
    • Verify the qualification and the mounting process match the assembly line.
    • Confirm the revision letter (base / V2 / V3) before comparing electrical rows.

    Frequently Asked Questions

    What is the operating temperature range?
    The rated range is quoted as ambient plus self-temperature rise, up to the maximum shown in the table. The part is qualified across that span, but the hot corner is where saturation and DCR must be checked.

    Does the automotive grade change the electrical values?
    Not by itself, but it changes the qualification and often the temperature range. Compare the rows of the automotive data sheet against the commercial one rather than assuming they match.

    Why do V2 and V3 parts exist?
    They are later revisions of the same body size with a changed electrical row – typically a higher current rating or an extra parameter such as self-resonant frequency. They are separate orderable parts, not substitutes.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products