Eaton HCM1A2213V2-150-R 15 uH Shielded Automotive Inductor
Eaton HCM1A2213V2-150-R 15 uH Shielded Automotive Inductor

Eaton HCM1A2213V2-150-R 15 uH Shielded Automotive Inductor

Share
Eaton HCM1A2213V2-150-R: AEC-Q200 automotive power inductor, 15 uH ±20%, 17 A Irms, Isat 24 A, DCR 4.92 mOhm, 22.78 x 22.3 mm.
    • Product Details
    • Download

    Eaton HCM1A2213V2-150-R 15 uH Shielded Automotive Inductor

    HCM1A2213V2-150-R at a glance: AEC-Q200 automotive power inductor, 15 uH ±20%, 17 A Irms, Isat 24 A (20% rolloff @ +25 °C), DCR 4.92 mOhm, 22.78 x 22.3 mm.

    Electrical Specifications

    ParameterValue
    Orderable part numberHCM1A2213V2-150-R
    OCL (open circuit inductance)15 uH ±20%
    FLL minimum, at Isat9.6 uH
    Irms (DC, 40 °C rise)17 A
    Isat (20% rolloff @ +25 °C)24 A
    DCR typical @ +20 °C4.92 mOhm
    DCR maximum @ +20 °C6 mOhm
    SRF typical5 MHz
    K-factor (Bp-p = K x L x dI)15, Bp-p in Gauss
    Package22.78 x 22.3 mm
    Height13.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10907

    Outline Drawing

    HCM1A2213V2-150-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10907: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    The Figures Explained

    Automotive power rails ask for two things a commercial inductor does not always give: a qualified construction and a saturation curve that is still usable at the hot corner. The molded powder core here provides both, with AEC-Q200 qualification and a soft rolloff that keeps inductance present at transient peak current.

    With 4.92 mOhm typical, the I-squared-R loss at the full 17 A rating is about 1.42 W. Compare that against the converter output power before deciding whether the part needs airflow or a copper pour under it.

    Saturation is quoted as 20% rolloff @ +25 °C. At that point the inductance has fallen to the stated fraction of its nominal value – the part is not damaged there, it simply stops behaving like the inductance on the label. Design the peak current to stay inside that boundary with margin for tolerance.

    Energy storage at the saturation current is around 4,320 uJ, the number that connects the inductance and the current rating into a single transient figure.

    The K-factor of 15 converts inductance and ripple into flux swing: each amp of peak-to-peak ripple moves the core through about 225 Gauss of Bp-p, the figure the core-loss curve is plotted against.

    Self-resonant frequency is 5 MHz typical. Above that the part becomes capacitive and stops behaving as an inductor, which is why the switching frequency and its first harmonics should stay well below it.

    Series Positioning

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    Within the HCM1A2213V2 family this is value 8 of 14, in a range that runs from 0.47 uH to 100 uH.

    Compared with its neighbours in the table, HCM1A2213V2-220-R trades 6.5 A of rated current for the next inductance step, which is the usual compromise in this family.

    • Core material: alloy powder core, 22.78 x 22.3 mm body at 13.0 mm.
    • Typical applications: body electronics; central body control module; headlamps, tail lamps and interior lighting and led lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control; advanced driver assistance systems.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Putting It to Work

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 6 mOhm becomes roughly 9.18 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Check Isat and DCR at the hot corner, not at +20 °C.
    • Check the hot-corner saturation margin against the worst-case load step.
    • Confirm the revision letter (base / V2 / V3) before comparing electrical rows.

    Frequently Asked Questions

    Does the automotive grade change the electrical values?
    Not by itself, but it changes the qualification and often the temperature range. Compare the rows of the automotive data sheet against the commercial one rather than assuming they match.

    Why do V2 and V3 parts exist?
    They are later revisions of the same body size with a changed electrical row – typically a higher current rating or an extra parameter such as self-resonant frequency. They are separate orderable parts, not substitutes.

    Why do V2 and V3 parts exist?
    They are later revisions of the same body size with a changed electrical row – typically a higher current rating or an extra parameter such as self-resonant frequency. They are separate orderable parts, not substitutes.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products