Eaton HCM1A2213V2-1R0-R 1.0 uH Automotive Power Inductor
Eaton HCM1A2213V2-1R0-R 1.0 uH Automotive Power Inductor

Eaton HCM1A2213V2-1R0-R 1.0 uH Automotive Power Inductor

Share
Eaton HCM1A2213V2-1R0-R: AEC-Q200 automotive power inductor, 1.0 uH ±20%, 50 A Irms, Isat 71 A, DCR 0.67 mOhm, 22.78 x 22.3 mm.
    • Product Details
    • Download

    Eaton HCM1A2213V2-1R0-R 1.0 uH Automotive Power Inductor

    HCM1A2213V2-1R0-R at a glance: AEC-Q200 automotive power inductor, 1.0 uH ±20%, 50 A Irms, Isat 71 A (20% rolloff @ +25 °C), DCR 0.67 mOhm, 22.78 x 22.3 mm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberHCM1A2213V2-1R0-R
    OCL (open circuit inductance)1.0 uH ±20%
    FLL minimum, at Isat0.64 uH
    Irms (DC, 40 °C rise)50 A
    Isat (20% rolloff @ +25 °C)71 A
    DCR typical @ +20 °C0.67 mOhm
    DCR maximum @ +20 °C0.84 mOhm
    SRF typical34 MHz
    K-factor (Bp-p = K x L x dI)53, Bp-p in Gauss
    Package22.78 x 22.3 mm
    Height13.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10907

    Mechanical Dimensions & Pad Layout

    HCM1A2213V2-1R0-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10907: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    The Figures Explained

    Automotive power rails ask for two things a commercial inductor does not always give: a qualified construction and a saturation curve that is still usable at the hot corner. The molded powder core here provides both, with AEC-Q200 qualification and a soft rolloff that keeps inductance present at transient peak current.

    Copper loss at the rated current works out to roughly 1.68 W from a typical DCR of 0.67 mOhm at 50 A. It is the number to start a thermal stack-up with, before core loss and before AC resistance rise.

    Isat is specified as 20% rolloff @ +25 °C, so the number is a rolloff criterion rather than an absolute maximum. The useful working range extends a little beyond it on a soft saturation core, but the loop compensation has to be designed for the inductance that remains.

    Stored energy at Isat is about 2,520 uJ, which is the energy the inductor hands to the load during a transient before the control loop reacts.

    With K = 53, a peak-to-peak ripple of one amp produces roughly 53 Gauss of flux swing. Read the core-loss graph at that amplitude and at the switching frequency to get the core contribution to the total loss.

    Self-resonant frequency is 34 MHz typical. Above that the part becomes capacitive and stops behaving as an inductor, which is why the switching frequency and its first harmonics should stay well below it.

    Where This Series Fits

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    Of the 14 values listed for HCM1A2213V2, this is the 2th, in a family covering 0.47 uH to 100 uH.

    One step down the table, HCM1A2213V2-R47-R, sits at 0.47 uH with 66 A and 0.4 mOhm – the lower inductance buys about 23.5 A of extra current in the same body.

    • Core material: alloy powder core, 22.78 x 22.3 mm body at 13.0 mm.
    • Typical applications: body electronics; central body control module; headlamps, tail lamps and interior lighting and led lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control; advanced driver assistance systems.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Design Notes

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 0.84 mOhm becomes roughly 1.29 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Verify the part marking for revision traceability in production.
    • Confirm the qualification file covers the module-level test plan.
    • Verify the part marking for revision traceability in production.

    Frequently Asked Questions

    Why do V2 and V3 parts exist?
    They are later revisions of the same body size with a changed electrical row – typically a higher current rating or an extra parameter such as self-resonant frequency. They are separate orderable parts, not substitutes.

    What does AEC-Q200 cover?
    The qualification regime for passive components in automotive use: thermal shock, temperature cycling, vibration, mechanical shock, moisture resistance and solderability, among others. It qualifies the construction, not the board design.

    What is the operating temperature range?
    The rated range is quoted as ambient plus self-temperature rise, up to the maximum shown in the table. The part is qualified across that span, but the hot corner is where saturation and DCR must be checked.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products