Eaton HCM1A2213V2-4R7-R AEC-Q200 Inductor 4.7 uH, Isat 37 A
Eaton HCM1A2213V2-4R7-R AEC-Q200 Inductor 4.7 uH, Isat 37 A

Eaton HCM1A2213V2-4R7-R AEC-Q200 Inductor 4.7 uH, Isat 37 A

Share
Eaton HCM1A2213V2-4R7-R: AEC-Q200 automotive power inductor, 4.7 uH ±20%, 33 A Irms, Isat 37 A, DCR 1.68 mOhm, 22.78 x 22.3 mm.
    • Product Details
    • Download

    Eaton HCM1A2213V2-4R7-R AEC-Q200 Inductor 4.7 uH, Isat 37 A

    HCM1A2213V2-4R7-R at a glance: AEC-Q200 automotive power inductor, 4.7 uH ±20%, 33 A Irms, Isat 37 A (20% rolloff @ +25 °C), DCR 1.68 mOhm, 22.78 x 22.3 mm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberHCM1A2213V2-4R7-R
    OCL (open circuit inductance)4.7 uH ±20%
    FLL minimum, at Isat3 uH
    Irms (DC, 40 °C rise)33 A
    Isat (20% rolloff @ +25 °C)37 A
    DCR typical @ +20 °C1.68 mOhm
    DCR maximum @ +20 °C1.85 mOhm
    SRF typical10 MHz
    K-factor (Bp-p = K x L x dI)28, Bp-p in Gauss
    Package22.78 x 22.3 mm
    Height13.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10907

    Dimensions and Pad Layout

    HCM1A2213V2-4R7-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10907: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    What the Numbers Mean

    This is the automotive version of the molded high-current inductor. The body is a molded powder core, the winding is shielded by the magnetic material itself, and the operating range runs to +155 °C. It is the part that goes on the DC-DC stages of body electronics, ADAS modules and infotainment head units.

    At the rated 33 A the winding dissipates about 1.83 W in copper alone, using the typical DCR of 1.68 mOhm. That figure is the floor of the loss budget: it assumes the current is pure DC, and any ripple adds to it.

    The Isat column is 20% rolloff @ +25 °C. Note what it does and does not mean: it is a defined rolloff point, not a destruction limit. Above it the inductance continues to fall, which is why the transient peak current should be checked against the curve, not just against the number.

    Energy storage at the saturation current is around 3,217 uJ, the number that connects the inductance and the current rating into a single transient figure.

    K-factor 28 means the flux swing is about 132 Gauss per amp of ripple. Core loss scales with the flux amplitude and the frequency, so this is the number to carry into the loss calculation rather than the inductance alone.

    Self-resonant frequency is 10 MHz typical. Above that the part becomes capacitive and stops behaving as an inductor, which is why the switching frequency and its first harmonics should stay well below it.

    What This Family Is For

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    Of the 14 values listed for HCM1A2213V2, this is the 5th, in a family covering 0.47 uH to 100 uH.

    The next value up in the same family, HCM1A2213V2-6R8-R, gives 6.8 uH at 26.5 A and DCR 2.5 mOhm: the extra inductance costs about 7.5 A of rated current.

    • Core material: alloy powder core, 22.78 x 22.3 mm body at 13.0 mm.
    • Typical applications: body electronics; central body control module; headlamps, tail lamps and interior lighting and led lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control; advanced driver assistance systems.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Putting It to Work

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 1.85 mOhm becomes roughly 2.83 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Confirm the qualification file covers the module-level test plan.
    • Check the hot-corner saturation margin against the worst-case load step.
    • Confirm the qualification file covers the module-level test plan.

    Frequently Asked Questions

    Is the part shielded for ADAS modules?
    The molded powder core encloses the winding, so the radiated field is small. That is why the family is used next to sensor front ends and camera interfaces.

    What does AEC-Q200 cover?
    The qualification regime for passive components in automotive use: thermal shock, temperature cycling, vibration, mechanical shock, moisture resistance and solderability, among others. It qualifies the construction, not the board design.

    What is the self-resonant frequency used for?
    It marks the point where the winding capacitance dominates. Keep the switching frequency and the harmonics that carry energy below it, and use it to compare candidates of the same inductance.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products