Eaton HCM1A2213V2-820-R AEC-Q200 Inductor 82 uH, Isat 9.5 A
Eaton HCM1A2213V2-820-R AEC-Q200 Inductor 82 uH, Isat 9.5 A

Eaton HCM1A2213V2-820-R AEC-Q200 Inductor 82 uH, Isat 9.5 A

Share
Eaton HCM1A2213V2-820-R: AEC-Q200 automotive power inductor, 82 uH ±20%, 7 A Irms, Isat 9.5 A, DCR 29.9 mOhm, 22.78 x 22.3 mm.
    • Product Details
    • Download

    Eaton HCM1A2213V2-820-R AEC-Q200 Inductor 82 uH, Isat 9.5 A

    HCM1A2213V2-820-R at a glance: AEC-Q200 automotive power inductor, 82 uH ±20%, 7 A Irms, Isat 9.5 A (20% rolloff @ +25 °C), DCR 29.9 mOhm, 22.78 x 22.3 mm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberHCM1A2213V2-820-R
    OCL (open circuit inductance)82 uH ±20%
    FLL minimum, at Isat52.5 uH
    Irms (DC, 40 °C rise)7 A
    Isat (20% rolloff @ +25 °C)9.5 A
    DCR typical @ +20 °C29.9 mOhm
    DCR maximum @ +20 °C34.3 mOhm
    SRF typical2 MHz
    K-factor (Bp-p = K x L x dI)5, Bp-p in Gauss
    Package22.78 x 22.3 mm
    Height13.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10907

    Dimensions and Pad Layout

    HCM1A2213V2-820-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10907: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    What the Numbers Mean

    AEC-Q200 qualified, molded, magnetically shielded, and rated to +155 °C ambient plus self-heating. The automotive grading is not a label on a commercial part: the test regime covers thermal shock, vibration and moisture, and the data sheet quotes the parameters at the temperature extremes the qualification demands.

    The DCR figure of 29.9 mOhm is what sets the efficiency: at 7 A the winding drops about 0.209 mV and dissipates 1.47 W. On a low-voltage rail that drop is a measurable fraction of the output, so the DCR column deserves as much attention as the inductance.

    The Isat column is 20% rolloff @ +25 °C. Note what it does and does not mean: it is a defined rolloff point, not a destruction limit. Above it the inductance continues to fall, which is why the transient peak current should be checked against the curve, not just against the number.

    Energy storage at the saturation current is around 3,700 uJ, the number that connects the inductance and the current rating into a single transient figure.

    K-factor 5 means the flux swing is about 410 Gauss per amp of ripple. Core loss scales with the flux amplitude and the frequency, so this is the number to carry into the loss calculation rather than the inductance alone.

    Self-resonant frequency is 2 MHz typical. Above that the part becomes capacitive and stops behaving as an inductor, which is why the switching frequency and its first harmonics should stay well below it.

    Positioning in the Range

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    In the HCM1A2213V2 line-up this part is number 13 of 14 by inductance, between 0.47 uH and 100 uH.

    Compared with its neighbours in the table, HCM1A2213V2-101-R trades 1.1 A of rated current for the next inductance step, which is the usual compromise in this family.

    • Core material: alloy powder core, 22.78 x 22.3 mm body at 13.0 mm.
    • Typical applications: body electronics; central body control module; headlamps, tail lamps and interior lighting and led lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control; advanced driver assistance systems.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Putting It to Work

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 34.3 mOhm becomes roughly 52.5 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Check the hot-corner saturation margin against the worst-case load step.
    • Check the hot-corner saturation margin against the worst-case load step.
    • Confirm the revision letter (base / V2 / V3) before comparing electrical rows.

    Frequently Asked Questions

    What is the self-resonant frequency used for?
    It marks the point where the winding capacitance dominates. Keep the switching frequency and the harmonics that carry energy below it, and use it to compare candidates of the same inductance.

    Why do V2 and V3 parts exist?
    They are later revisions of the same body size with a changed electrical row – typically a higher current rating or an extra parameter such as self-resonant frequency. They are separate orderable parts, not substitutes.

    What is the self-resonant frequency used for?
    It marks the point where the winding capacitance dominates. Keep the switching frequency and the harmonics that carry energy below it, and use it to compare candidates of the same inductance.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products