Eaton HCM1A4020V2-2R2-R 2.2 uH AEC-Q200 Inductor, 4.6 A
Eaton HCM1A4020V2-2R2-R 2.2 uH AEC-Q200 Inductor, 4.6 A

Eaton HCM1A4020V2-2R2-R 2.2 uH AEC-Q200 Inductor, 4.6 A

Share
Eaton HCM1A4020V2-2R2-R: AEC-Q200 automotive power inductor, 2.2 uH ±20%, 4.6 A Irms, Isat 5 A, DCR 40 mOhm, 4.75 x 4.45 mm.
    • Product Details
    • Download

    Eaton HCM1A4020V2-2R2-R 2.2 uH AEC-Q200 Inductor, 4.6 A

    HCM1A4020V2-2R2-R at a glance: AEC-Q200 automotive power inductor, 2.2 uH ±20%, 4.6 A Irms, Isat 5 A (20% rolloff @ +25 °C), DCR 40 mOhm, 4.75 x 4.45 mm.

    Specification Table

    ParameterValue
    Orderable part numberHCM1A4020V2-2R2-R
    OCL (open circuit inductance)2.2 uH ±20%
    FLL minimum, at Isat1.23 uH
    Irms (DC, 40 °C rise)4.6 A
    Isat (20% rolloff @ +25 °C)5 A
    DCR typical @ +20 °C40 mOhm
    DCR maximum @ +20 °C48 mOhm
    SRF typical40 MHz
    K-factor (Bp-p = K x L x dI)711, Bp-p in Gauss
    Package4.75 x 4.45 mm
    Height2.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10908

    Dimensions and Pad Layout

    HCM1A4020V2-2R2-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10908: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    The Figures Explained

    Automotive power rails ask for two things a commercial inductor does not always give: a qualified construction and a saturation curve that is still usable at the hot corner. The molded powder core here provides both, with AEC-Q200 qualification and a soft rolloff that keeps inductance present at transient peak current.

    Copper loss at the rated current works out to roughly 0.846 W from a typical DCR of 40 mOhm at 4.6 A. It is the number to start a thermal stack-up with, before core loss and before AC resistance rise.

    Saturation is quoted as 20% rolloff @ +25 °C. At that point the inductance has fallen to the stated fraction of its nominal value – the part is not damaged there, it simply stops behaving like the inductance on the label. Design the peak current to stay inside that boundary with margin for tolerance.

    At Isat the part holds about 27.5 uJ. On a multiphase rail that is the energy per phase available to bridge a load step, which sets how much bulk capacitance the controller still needs.

    With K = 711, a peak-to-peak ripple of one amp produces roughly 1,564 Gauss of flux swing. Read the core-loss graph at that amplitude and at the switching frequency to get the core contribution to the total loss.

    Self-resonant frequency is 40 MHz typical. Above that the part becomes capacitive and stops behaving as an inductor, which is why the switching frequency and its first harmonics should stay well below it.

    Where This Series Fits

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    In the HCM1A4020V2 line-up this part is number 10 of 15 by inductance, between 0.1 uH and 15 uH.

    The next value up in the same family, HCM1A4020V2-3R3-R, gives 3.3 uH at 3.1 A and DCR 71 mOhm: the extra inductance costs about 1.4 A of rated current.

    • Core material: alloy powder core, 4.75 x 4.45 mm body at 2.0 mm.
    • Typical applications: body electronics; central body control module; vehicle access control system; headlamps, tail lamps and interior lighting and led lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Sizing It Into a Design

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 48 mOhm becomes roughly 73.5 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Confirm the revision letter (base / V2 / V3) before comparing electrical rows.
    • Confirm the revision letter (base / V2 / V3) before comparing electrical rows.
    • Verify the part marking for revision traceability in production.

    Frequently Asked Questions

    Why do V2 and V3 parts exist?
    They are later revisions of the same body size with a changed electrical row – typically a higher current rating or an extra parameter such as self-resonant frequency. They are separate orderable parts, not substitutes.

    What does AEC-Q200 cover?
    The qualification regime for passive components in automotive use: thermal shock, temperature cycling, vibration, mechanical shock, moisture resistance and solderability, among others. It qualifies the construction, not the board design.

    Is the part shielded for ADAS modules?
    The molded powder core encloses the winding, so the radiated field is small. That is why the family is used next to sensor front ends and camera interfaces.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message