Eaton HCM1A4020V2-6R8-R 6.8 uH Automotive Power Inductor
Eaton HCM1A4020V2-6R8-R 6.8 uH Automotive Power Inductor

Eaton HCM1A4020V2-6R8-R 6.8 uH Automotive Power Inductor

Share
Eaton HCM1A4020V2-6R8-R: AEC-Q200 automotive power inductor, 6.8 uH ±20%, 1.7 A Irms, Isat 2.6 A, DCR 167 mOhm, 4.75 x 4.45 mm.
    • Product Details
    • Download

    Eaton HCM1A4020V2-6R8-R 6.8 uH Automotive Power Inductor

    HCM1A4020V2-6R8-R at a glance: AEC-Q200 automotive power inductor, 6.8 uH ±20%, 1.7 A Irms, Isat 2.6 A (20% rolloff @ +25 °C), DCR 167 mOhm, 4.75 x 4.45 mm.

    Electrical Specifications

    ParameterValue
    Orderable part numberHCM1A4020V2-6R8-R
    OCL (open circuit inductance)6.8 uH ±20%
    FLL minimum, at Isat3.8 uH
    Irms (DC, 40 °C rise)1.7 A
    Isat (20% rolloff @ +25 °C)2.6 A
    DCR typical @ +20 °C167 mOhm
    DCR maximum @ +20 °C192 mOhm
    SRF typical23 MHz
    K-factor (Bp-p = K x L x dI)511, Bp-p in Gauss
    Package4.75 x 4.45 mm
    Height2.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10908

    Outline Drawing

    HCM1A4020V2-6R8-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10908: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    How to Read These Ratings

    This is the automotive version of the molded high-current inductor. The body is a molded powder core, the winding is shielded by the magnetic material itself, and the operating range runs to +155 °C. It is the part that goes on the DC-DC stages of body electronics, ADAS modules and infotainment head units.

    Copper loss at the rated current works out to roughly 0.483 W from a typical DCR of 167 mOhm at 1.7 A. It is the number to start a thermal stack-up with, before core loss and before AC resistance rise.

    The Isat column is 20% rolloff @ +25 °C. Note what it does and does not mean: it is a defined rolloff point, not a destruction limit. Above it the inductance continues to fall, which is why the transient peak current should be checked against the curve, not just against the number.

    Energy storage at the saturation current is around 23 uJ, the number that connects the inductance and the current rating into a single transient figure.

    K-factor 511 means the flux swing is about 3,475 Gauss per amp of ripple. Core loss scales with the flux amplitude and the frequency, so this is the number to carry into the loss calculation rather than the inductance alone.

    Self-resonant frequency is 23 MHz typical. Above that the part becomes capacitive and stops behaving as an inductor, which is why the switching frequency and its first harmonics should stay well below it.

    What This Family Is For

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    Of the 15 values listed for HCM1A4020V2, this is the 13th, in a family covering 0.1 uH to 15 uH.

    Compared with its neighbours in the table, HCM1A4020V2-100-R trades 0.9 A of rated current for the next inductance step, which is the usual compromise in this family.

    • Core material: alloy powder core, 4.75 x 4.45 mm body at 2.0 mm.
    • Typical applications: body electronics; central body control module; vehicle access control system; headlamps, tail lamps and interior lighting and led lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Putting It to Work

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 192 mOhm becomes roughly 294 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Verify the part marking for revision traceability in production.
    • Confirm the qualification file covers the module-level test plan.
    • Confirm the qualification file covers the module-level test plan.

    Frequently Asked Questions

    Does the automotive grade change the electrical values?
    Not by itself, but it changes the qualification and often the temperature range. Compare the rows of the automotive data sheet against the commercial one rather than assuming they match.

    What does AEC-Q200 cover?
    The qualification regime for passive components in automotive use: thermal shock, temperature cycling, vibration, mechanical shock, moisture resistance and solderability, among others. It qualifies the construction, not the board design.

    What is the self-resonant frequency used for?
    It marks the point where the winding capacitance dominates. Keep the switching frequency and the harmonics that carry energy below it, and use it to compare candidates of the same inductance.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products