Eaton HCM1A4020V3-4R7-R 4.7 uH Automotive Power Inductor
Eaton HCM1A4020V3-4R7-R 4.7 uH Automotive Power Inductor

Eaton HCM1A4020V3-4R7-R 4.7 uH Automotive Power Inductor

Share
Eaton HCM1A4020V3-4R7-R: AEC-Q200 automotive power inductor, 4.7 uH ±20%, 2.5 A Irms, Isat 3.2 A, DCR 98 mOhm, 4.75 x 4.45 mm.
    • Product Details
    • Download

    Eaton HCM1A4020V3-4R7-R 4.7 uH Automotive Power Inductor

    HCM1A4020V3-4R7-R at a glance: AEC-Q200 automotive power inductor, 4.7 uH ±20%, 2.5 A Irms, Isat 3.2 A (20% rolloff @ +25 °C), DCR 98 mOhm, 4.75 x 4.45 mm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberHCM1A4020V3-4R7-R
    OCL (open circuit inductance)4.7 uH ±20%
    FLL minimum, at Isat2.63 uH
    Irms (DC, 40 °C rise)2.5 A
    Isat (20% rolloff @ +25 °C)3.2 A
    DCR typical @ +20 °C98 mOhm
    DCR maximum @ +20 °C118 mOhm
    SRF typical27 MHz
    K-factor (Bp-p = K x L x dI)966, Bp-p in Gauss
    Package4.75 x 4.45 mm
    Height2.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data ELX1495

    Mechanical Dimensions & Pad Layout

    HCM1A4020V3-4R7-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data ELX1495: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    How to Read These Ratings

    AEC-Q200 qualified, molded, magnetically shielded, and rated to +155 °C ambient plus self-heating. The automotive grading is not a label on a commercial part: the test regime covers thermal shock, vibration and moisture, and the data sheet quotes the parameters at the temperature extremes the qualification demands.

    With 98 mOhm typical, the I-squared-R loss at the full 2.5 A rating is about 0.613 W. Compare that against the converter output power before deciding whether the part needs airflow or a copper pour under it.

    The saturation rating reads 20% rolloff @ +25 °C. Treat it as the edge of the linear region: below it the inductance is within tolerance, above it the value droops. For a current-mode converter that means the peak current at the worst-case load step is what must fit under this number.

    The core stores roughly 24.1 uJ at the saturation point – a useful figure when sizing the output capacitance that has to absorb the same transient.

    K-factor 966 means the flux swing is about 4,540 Gauss per amp of ripple. Core loss scales with the flux amplitude and the frequency, so this is the number to carry into the loss calculation rather than the inductance alone.

    Self-resonant frequency is 27 MHz typical. Above that the part becomes capacitive and stops behaving as an inductor, which is why the switching frequency and its first harmonics should stay well below it.

    Positioning in the Range

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    The HCM1A4020V3 family spans 0.1 uH to 15 uH; this row sits at position 12 of 15.

    The next value up in the same family, HCM1A4020V3-6R8-R, gives 6.8 uH at 1.7 A and DCR 167 mOhm: the extra inductance costs about 1.4 A of rated current.

    • Core material: alloy powder core, 4.75 x 4.45 mm body at 2.0 mm.
    • Typical applications: body electronics; central body control module; vehicle access control system; headlamps, tail lamps and interior lighting and led lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Sizing and Layout Notes

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 118 mOhm becomes roughly 181 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Verify the part marking for revision traceability in production.
    • Check the hot-corner saturation margin against the worst-case load step.
    • Confirm the revision letter (base / V2 / V3) before comparing electrical rows.

    Frequently Asked Questions

    Why do V2 and V3 parts exist?
    They are later revisions of the same body size with a changed electrical row – typically a higher current rating or an extra parameter such as self-resonant frequency. They are separate orderable parts, not substitutes.

    Why do V2 and V3 parts exist?
    They are later revisions of the same body size with a changed electrical row – typically a higher current rating or an extra parameter such as self-resonant frequency. They are separate orderable parts, not substitutes.

    Does the automotive grade change the electrical values?
    Not by itself, but it changes the qualification and often the temperature range. Compare the rows of the automotive data sheet against the commercial one rather than assuming they match.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products