Eaton HCM1A4020V3-6R8-R 6.8 uH AEC-Q200 Inductor, 1.7 A
Eaton HCM1A4020V3-6R8-R 6.8 uH AEC-Q200 Inductor, 1.7 A

Eaton HCM1A4020V3-6R8-R 6.8 uH AEC-Q200 Inductor, 1.7 A

Share
Eaton HCM1A4020V3-6R8-R: AEC-Q200 automotive power inductor, 6.8 uH ±20%, 1.7 A Irms, Isat 2.6 A, DCR 167 mOhm, 4.75 x 4.45 mm.
    • Product Details
    • Download

    Eaton HCM1A4020V3-6R8-R 6.8 uH AEC-Q200 Inductor, 1.7 A

    HCM1A4020V3-6R8-R at a glance: AEC-Q200 automotive power inductor, 6.8 uH ±20%, 1.7 A Irms, Isat 2.6 A (20% rolloff @ +25 °C), DCR 167 mOhm, 4.75 x 4.45 mm.

    Specification Table

    ParameterValue
    Orderable part numberHCM1A4020V3-6R8-R
    OCL (open circuit inductance)6.8 uH ±20%
    FLL minimum, at Isat3.8 uH
    Irms (DC, 40 °C rise)1.7 A
    Isat (20% rolloff @ +25 °C)2.6 A
    DCR typical @ +20 °C167 mOhm
    DCR maximum @ +20 °C192 mOhm
    SRF typical23 MHz
    K-factor (Bp-p = K x L x dI)771, Bp-p in Gauss
    Package4.75 x 4.45 mm
    Height2.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data ELX1495

    Outline Drawing

    HCM1A4020V3-6R8-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data ELX1495: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    How to Read These Ratings

    This is the automotive version of the molded high-current inductor. The body is a molded powder core, the winding is shielded by the magnetic material itself, and the operating range runs to +155 °C. It is the part that goes on the DC-DC stages of body electronics, ADAS modules and infotainment head units.

    With 167 mOhm typical, the I-squared-R loss at the full 1.7 A rating is about 0.483 W. Compare that against the converter output power before deciding whether the part needs airflow or a copper pour under it.

    The saturation rating reads 20% rolloff @ +25 °C. Treat it as the edge of the linear region: below it the inductance is within tolerance, above it the value droops. For a current-mode converter that means the peak current at the worst-case load step is what must fit under this number.

    Energy storage at the saturation current is around 23 uJ, the number that connects the inductance and the current rating into a single transient figure.

    The K-factor of 771 converts inductance and ripple into flux swing: each amp of peak-to-peak ripple moves the core through about 5,243 Gauss of Bp-p, the figure the core-loss curve is plotted against.

    Self-resonant frequency is 23 MHz typical. Above that the part becomes capacitive and stops behaving as an inductor, which is why the switching frequency and its first harmonics should stay well below it.

    Positioning in the Range

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    Within the HCM1A4020V3 family this is value 13 of 15, in a range that runs from 0.1 uH to 15 uH.

    Compared with its neighbours in the table, HCM1A4020V3-100-R trades 0.9 A of rated current for the next inductance step, which is the usual compromise in this family.

    • Core material: alloy powder core, 4.75 x 4.45 mm body at 2.0 mm.
    • Typical applications: body electronics; central body control module; vehicle access control system; headlamps, tail lamps and interior lighting and led lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Sizing and Layout Notes

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 192 mOhm becomes roughly 294 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Check Isat and DCR at the hot corner, not at +20 °C.
    • Confirm the revision letter (base / V2 / V3) before comparing electrical rows.
    • Confirm the qualification file covers the module-level test plan.

    Frequently Asked Questions

    Is the part shielded for ADAS modules?
    The molded powder core encloses the winding, so the radiated field is small. That is why the family is used next to sensor front ends and camera interfaces.

    Why do V2 and V3 parts exist?
    They are later revisions of the same body size with a changed electrical row – typically a higher current rating or an extra parameter such as self-resonant frequency. They are separate orderable parts, not substitutes.

    Why do V2 and V3 parts exist?
    They are later revisions of the same body size with a changed electrical row – typically a higher current rating or an extra parameter such as self-resonant frequency. They are separate orderable parts, not substitutes.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products