Eaton HCM1A4020V3-R10-R 0.10 uH AEC-Q200 Inductor, 16 A
Eaton HCM1A4020V3-R10-R 0.10 uH AEC-Q200 Inductor, 16 A

Eaton HCM1A4020V3-R10-R 0.10 uH AEC-Q200 Inductor, 16 A

Share
Eaton HCM1A4020V3-R10-R: AEC-Q200 automotive power inductor, 0.10 uH ±20%, 16 A Irms, Isat 22 A, DCR 3.1 mOhm, 4.75 x 4.45 mm.
    • Product Details
    • Download

    Eaton HCM1A4020V3-R10-R 0.10 uH AEC-Q200 Inductor, 16 A

    HCM1A4020V3-R10-R at a glance: AEC-Q200 automotive power inductor, 0.10 uH ±20%, 16 A Irms, Isat 22 A (20% rolloff @ +25 °C), DCR 3.1 mOhm, 4.75 x 4.45 mm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberHCM1A4020V3-R10-R
    OCL (open circuit inductance)0.10 uH ±20%
    FLL minimum, at Isat0.056 uH
    Irms (DC, 40 °C rise)16 A
    Isat (20% rolloff @ +25 °C)22 A
    DCR typical @ +20 °C3.1 mOhm
    DCR maximum @ +20 °C4 mOhm
    SRF typical310 MHz
    K-factor (Bp-p = K x L x dI)3,140, Bp-p in Gauss
    Package4.75 x 4.45 mm
    Height2.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data ELX1495

    Mechanical Dimensions & Pad Layout

    HCM1A4020V3-R10-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data ELX1495: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    What the Numbers Mean

    AEC-Q200 qualified, molded, magnetically shielded, and rated to +155 °C ambient plus self-heating. The automotive grading is not a label on a commercial part: the test regime covers thermal shock, vibration and moisture, and the data sheet quotes the parameters at the temperature extremes the qualification demands.

    At the rated 16 A the winding dissipates about 0.794 W in copper alone, using the typical DCR of 3.1 mOhm. That figure is the floor of the loss budget: it assumes the current is pure DC, and any ripple adds to it.

    Saturation is quoted as 20% rolloff @ +25 °C. At that point the inductance has fallen to the stated fraction of its nominal value – the part is not damaged there, it simply stops behaving like the inductance on the label. Design the peak current to stay inside that boundary with margin for tolerance.

    The core stores roughly 24.2 uJ at the saturation point – a useful figure when sizing the output capacitance that has to absorb the same transient.

    With K = 3,140, a peak-to-peak ripple of one amp produces roughly 314 Gauss of flux swing. Read the core-loss graph at that amplitude and at the switching frequency to get the core contribution to the total loss.

    Self-resonant frequency is 310 MHz typical. Above that the part becomes capacitive and stops behaving as an inductor, which is why the switching frequency and its first harmonics should stay well below it.

    Where This Series Fits

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    Within the HCM1A4020V3 family this is value 1 of 15, in a range that runs from 0.1 uH to 15 uH.

    One step down the table, HCM1A4020V3-R22-R, sits at 0.22 uH with 11 A and 5.5 mOhm – the lower inductance buys about 0 A of extra current in the same body.

    • Core material: alloy powder core, 4.75 x 4.45 mm body at 2.0 mm.
    • Typical applications: body electronics; central body control module; vehicle access control system; headlamps, tail lamps and interior lighting and led lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Putting It to Work

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 4 mOhm becomes roughly 6.12 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Verify the part marking for revision traceability in production.
    • Check the hot-corner saturation margin against the worst-case load step.
    • Check Isat and DCR at the hot corner, not at +20 °C.

    Frequently Asked Questions

    What is the self-resonant frequency used for?
    It marks the point where the winding capacitance dominates. Keep the switching frequency and the harmonics that carry energy below it, and use it to compare candidates of the same inductance.

    Does the automotive grade change the electrical values?
    Not by itself, but it changes the qualification and often the temperature range. Compare the rows of the automotive data sheet against the commercial one rather than assuming they match.

    What is the operating temperature range?
    The rated range is quoted as ambient plus self-temperature rise, up to the maximum shown in the table. The part is qualified across that span, but the hot corner is where saturation and DCR must be checked.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message