Eaton HCM1A4020V3-R33-R AEC-Q200 Inductor 0.33 uH, Isat 12 A
Eaton HCM1A4020V3-R33-R AEC-Q200 Inductor 0.33 uH, Isat 12 A

Eaton HCM1A4020V3-R33-R AEC-Q200 Inductor 0.33 uH, Isat 12 A

Share
Eaton HCM1A4020V3-R33-R: AEC-Q200 automotive power inductor, 0.33 uH ±20%, 8.5 A Irms, Isat 12 A, DCR 7.5 mOhm, 4.75 x 4.45 mm.
    • Product Details
    • Download

    Eaton HCM1A4020V3-R33-R AEC-Q200 Inductor 0.33 uH, Isat 12 A

    HCM1A4020V3-R33-R at a glance: AEC-Q200 automotive power inductor, 0.33 uH ±20%, 8.5 A Irms, Isat 12 A (20% rolloff @ +25 °C), DCR 7.5 mOhm, 4.75 x 4.45 mm.

    Specification Table

    ParameterValue
    Orderable part numberHCM1A4020V3-R33-R
    OCL (open circuit inductance)0.33 uH ±20%
    FLL minimum, at Isat0.185 uH
    Irms (DC, 40 °C rise)8.5 A
    Isat (20% rolloff @ +25 °C)12 A
    DCR typical @ +20 °C7.5 mOhm
    DCR maximum @ +20 °C9 mOhm
    SRF typical130 MHz
    K-factor (Bp-p = K x L x dI)2,102, Bp-p in Gauss
    Package4.75 x 4.45 mm
    Height2.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data ELX1495

    Mechanical Dimensions & Pad Layout

    HCM1A4020V3-R33-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data ELX1495: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    How to Read These Ratings

    AEC-Q200 qualified, molded, magnetically shielded, and rated to +155 °C ambient plus self-heating. The automotive grading is not a label on a commercial part: the test regime covers thermal shock, vibration and moisture, and the data sheet quotes the parameters at the temperature extremes the qualification demands.

    With 7.5 mOhm typical, the I-squared-R loss at the full 8.5 A rating is about 0.542 W. Compare that against the converter output power before deciding whether the part needs airflow or a copper pour under it.

    The saturation rating reads 20% rolloff @ +25 °C. Treat it as the edge of the linear region: below it the inductance is within tolerance, above it the value droops. For a current-mode converter that means the peak current at the worst-case load step is what must fit under this number.

    Stored energy at Isat is about 23.8 uJ, which is the energy the inductor hands to the load during a transient before the control loop reacts.

    The K-factor of 2,102 converts inductance and ripple into flux swing: each amp of peak-to-peak ripple moves the core through about 694 Gauss of Bp-p, the figure the core-loss curve is plotted against.

    Self-resonant frequency is 130 MHz typical. Above that the part becomes capacitive and stops behaving as an inductor, which is why the switching frequency and its first harmonics should stay well below it.

    Positioning in the Range

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    Of the 15 values listed for HCM1A4020V3, this is the 3th, in a family covering 0.1 uH to 15 uH.

    The next value up in the same family, HCM1A4020V3-R47-R, gives 0.47 uH at 7.3 A and DCR 10.5 mOhm: the extra inductance costs about 3.7 A of rated current.

    • Core material: alloy powder core, 4.75 x 4.45 mm body at 2.0 mm.
    • Typical applications: body electronics; central body control module; vehicle access control system; headlamps, tail lamps and interior lighting and led lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Design Notes

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 9 mOhm becomes roughly 13.8 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Check the hot-corner saturation margin against the worst-case load step.
    • Verify the part marking for revision traceability in production.
    • Verify the qualification and the mounting process match the assembly line.

    Frequently Asked Questions

    Why do V2 and V3 parts exist?
    They are later revisions of the same body size with a changed electrical row – typically a higher current rating or an extra parameter such as self-resonant frequency. They are separate orderable parts, not substitutes.

    Why do V2 and V3 parts exist?
    They are later revisions of the same body size with a changed electrical row – typically a higher current rating or an extra parameter such as self-resonant frequency. They are separate orderable parts, not substitutes.

    What does AEC-Q200 cover?
    The qualification regime for passive components in automotive use: thermal shock, temperature cycling, vibration, mechanical shock, moisture resistance and solderability, among others. It qualifies the construction, not the board design.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products