Eaton HCM1A4020V3-R68-R 0.68 uH Shielded Automotive Inductor
Eaton HCM1A4020V3-R68-R 0.68 uH Shielded Automotive Inductor

Eaton HCM1A4020V3-R68-R 0.68 uH Shielded Automotive Inductor

Share
Eaton HCM1A4020V3-R68-R: AEC-Q200 automotive power inductor, 0.68 uH ±20%, 6.7 A Irms, Isat 9 A, DCR 12.5 mOhm, 4.75 x 4.45 mm.
    • Product Details
    • Download

    Eaton HCM1A4020V3-R68-R 0.68 uH Shielded Automotive Inductor

    HCM1A4020V3-R68-R at a glance: AEC-Q200 automotive power inductor, 0.68 uH ±20%, 6.7 A Irms, Isat 9 A (20% rolloff @ +25 °C), DCR 12.5 mOhm, 4.75 x 4.45 mm.

    Specification Table

    ParameterValue
    Orderable part numberHCM1A4020V3-R68-R
    OCL (open circuit inductance)0.68 uH ±20%
    FLL minimum, at Isat0.381 uH
    Irms (DC, 40 °C rise)6.7 A
    Isat (20% rolloff @ +25 °C)9 A
    DCR typical @ +20 °C12.5 mOhm
    DCR maximum @ +20 °C16 mOhm
    SRF typical85 MHz
    K-factor (Bp-p = K x L x dI)2,021, Bp-p in Gauss
    Package4.75 x 4.45 mm
    Height2.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +155 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data ELX1495

    Dimensions and Pad Layout

    HCM1A4020V3-R68-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data ELX1495: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    How to Read These Ratings

    AEC-Q200 qualified, molded, magnetically shielded, and rated to +155 °C ambient plus self-heating. The automotive grading is not a label on a commercial part: the test regime covers thermal shock, vibration and moisture, and the data sheet quotes the parameters at the temperature extremes the qualification demands.

    Copper loss at the rated current works out to roughly 0.561 W from a typical DCR of 12.5 mOhm at 6.7 A. It is the number to start a thermal stack-up with, before core loss and before AC resistance rise.

    The saturation rating reads 20% rolloff @ +25 °C. Treat it as the edge of the linear region: below it the inductance is within tolerance, above it the value droops. For a current-mode converter that means the peak current at the worst-case load step is what must fit under this number.

    Energy storage at the saturation current is around 27.5 uJ, the number that connects the inductance and the current rating into a single transient figure.

    The K-factor of 2,021 converts inductance and ripple into flux swing: each amp of peak-to-peak ripple moves the core through about 1,374 Gauss of Bp-p, the figure the core-loss curve is plotted against.

    Self-resonant frequency is 85 MHz typical. Above that the part becomes capacitive and stops behaving as an inductor, which is why the switching frequency and its first harmonics should stay well below it.

    What This Family Is For

    The HCM1A family is the automotive molded range: AEC-Q200 qualified, rated to +155 °C, from a 5 mm footprint up to a 22 mm body. Several sizes carry a V2 or V3 revision with a higher current rating or an extra saturation column, so the revision letter is part of the specification.

    Within the HCM1A4020V3 family this is value 6 of 15, in a range that runs from 0.1 uH to 15 uH.

    One step down the table, HCM1A4020V3-R56-R, sits at 0.56 uH with 7.3 A and 12 mOhm – the lower inductance buys about 1.2 A of extra current in the same body.

    • Core material: alloy powder core, 4.75 x 4.45 mm body at 2.0 mm.
    • Typical applications: body electronics; central body control module; vehicle access control system; headlamps, tail lamps and interior lighting and led lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control.
    • The +155 °C rating is ambient plus self-temperature rise. Derate against the hot DCR, not the +20 °C value, when the board sits in a warm enclosure.

    Sizing and Layout Notes

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 16 mOhm becomes roughly 24.5 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the revision letter changes the electrical row. V2 and V3 parts of the same body size are not drop-in substitutes for the base part; compare the tables row by row.

    • Check the hot-corner saturation margin against the worst-case load step.
    • Confirm the qualification file covers the module-level test plan.
    • Verify the qualification and the mounting process match the assembly line.

    Frequently Asked Questions

    Is the part shielded for ADAS modules?
    The molded powder core encloses the winding, so the radiated field is small. That is why the family is used next to sensor front ends and camera interfaces.

    What does AEC-Q200 cover?
    The qualification regime for passive components in automotive use: thermal shock, temperature cycling, vibration, mechanical shock, moisture resistance and solderability, among others. It qualifies the construction, not the board design.

    Why do V2 and V3 parts exist?
    They are later revisions of the same body size with a changed electrical row – typically a higher current rating or an extra parameter such as self-resonant frequency. They are separate orderable parts, not substitutes.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products