Eaton HCMA0503-2R2-R 2.2 uH AEC-Q200 Inductor, 6.8 A
Eaton HCMA0503-2R2-R 2.2 uH AEC-Q200 Inductor, 6.8 A

Eaton HCMA0503-2R2-R 2.2 uH AEC-Q200 Inductor, 6.8 A

Share
Eaton HCMA0503-2R2-R: AEC-Q200 high-current inductor, 2.2 uH ±20%, 6.8 A Irms, Isat 6.5 A, DCR 22.5 mOhm, 5.5 x 5.3 mm.
    • Product Details
    • Download

    Eaton HCMA0503-2R2-R 2.2 uH AEC-Q200 Inductor, 6.8 A

    HCMA0503-2R2-R at a glance: AEC-Q200 high-current inductor, 2.2 uH ±20%, 6.8 A Irms, Isat 6.5 A (20% rolloff @ +25 °C), DCR 22.5 mOhm, 5.5 x 5.3 mm.

    Key Specifications

    ParameterValue
    Orderable part numberHCMA0503-2R2-R
    OCL (open circuit inductance)2.2 uH ±20%
    FLL minimum, at Isat1.4 uH
    Irms (DC, 40 °C rise)6.8 A
    Isat (20% rolloff @ +25 °C)6.5 A
    DCR typical @ +20 °C22.5 mOhm
    DCR maximum @ +20 °C25 mOhm
    K-factor (Bp-p = K x L x dI)325, Bp-p in Gauss
    Package5.5 x 5.3 mm
    Height3.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +125 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10248

    Mechanical Drawing

    HCMA0503-2R2-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10248: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    What the Numbers Mean

    This is the high-current member of the automotive molded family. Where the standard automotive parts top out at a few tens of amps, this one is built for the main DC-DC stage: thicker winding, larger body, and a saturation current that scales with it.

    At the rated 6.8 A the winding dissipates about 1.04 W in copper alone, using the typical DCR of 22.5 mOhm. That figure is the floor of the loss budget: it assumes the current is pure DC, and any ripple adds to it.

    The Isat column is 20% rolloff @ +25 °C. Note what it does and does not mean: it is a defined rolloff point, not a destruction limit. Above it the inductance continues to fall, which is why the transient peak current should be checked against the curve, not just against the number.

    Stored energy at Isat is about 46.5 uJ, which is the energy the inductor hands to the load during a transient before the control loop reacts.

    The K-factor of 325 converts inductance and ripple into flux swing: each amp of peak-to-peak ripple moves the core through about 715 Gauss of Bp-p, the figure the core-loss curve is plotted against.

    What This Family Is For

    The HCMA family is the automotive high-current molded range, rated to +125 °C. It shares body sizes with the commercial HCM parts but is qualified and characterised for automotive use, with the current ratings to match the larger winding section.

    In the HCMA0503 line-up this part is number 7 of 14 by inductance, between 0.2 uH and 22 uH.

    Compared with its neighbours in the table, HCMA0503-3R3-R trades 2 A of rated current for the next inductance step, which is the usual compromise in this family.

    • Core material: iron powder core, 5.5 x 5.3 mm body at 3.0 mm.
    • Typical applications: body electronics; central body control module; vehicle access control system; headlamps, tail lamps and interior lighting; heating ventilation and air conditioning con­ trollers (hvac); doors, window lift and seat control.
    • Automotive derating practice: size against the saturation current at the hot corner and keep margin for the load transient, not just the steady-state current.

    Sizing It Into a Design

    Copper resistance rises with temperature, so at the +125 °C limit the maximum DCR of 25 mOhm becomes roughly 35.3 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the AEC-Q200 grade covers the construction, not the thermal design of your board. The loss calculation is still the engineer’s job.

    • Check the terminal spacing against the rail voltage and the coating scheme.
    • Check the terminal spacing against the rail voltage and the coating scheme.
    • Check the terminal spacing against the rail voltage and the coating scheme.

    Frequently Asked Questions

    Is this part suitable for a 48 V rail?
    The electrical ratings suit it, but isolation and creepage are board-level decisions. Check terminal spacing and any coating against the rail voltage.

    Is it shielded?
    Yes – the winding is enclosed in the molded powder core, which keeps the external field low enough for dense automotive boards.

    How does this differ from the commercial HCM part?
    Same molded construction and similar body sizes, but automotive qualified, characterised to +125 °C, and wound for higher current in the larger sizes. The electrical rows are not interchangeable.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products