Eaton HCMA0503-R20-R AEC-Q200 Inductor 0.20 uH, Isat 21 A
Eaton HCMA0503-R20-R AEC-Q200 Inductor 0.20 uH, Isat 21 A

Eaton HCMA0503-R20-R AEC-Q200 Inductor 0.20 uH, Isat 21 A

Share
Eaton HCMA0503-R20-R: AEC-Q200 high-current inductor, 0.20 uH ±20%, 22.2 A Irms, Isat 21 A, DCR 2.1 mOhm, 5.5 x 5.3 mm.
    • Product Details
    • Download

    Eaton HCMA0503-R20-R AEC-Q200 Inductor 0.20 uH, Isat 21 A

    HCMA0503-R20-R at a glance: AEC-Q200 high-current inductor, 0.20 uH ±20%, 22.2 A Irms, Isat 21 A (20% rolloff @ +25 °C), DCR 2.1 mOhm, 5.5 x 5.3 mm.

    Electrical Specifications

    ParameterValue
    Orderable part numberHCMA0503-R20-R
    OCL (open circuit inductance)0.20 uH ±20%
    FLL minimum, at Isat0.13 uH
    Irms (DC, 40 °C rise)22.2 A
    Isat (20% rolloff @ +25 °C)21 A
    DCR typical @ +20 °C2.1 mOhm
    DCR maximum @ +20 °C2.31 mOhm
    K-factor (Bp-p = K x L x dI)1,764, Bp-p in Gauss
    Package5.5 x 5.3 mm
    Height3.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +125 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10248

    Mechanical Drawing

    HCMA0503-R20-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10248: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    Reading the Data Sheet

    The family takes the molded construction used on the commercial high-current parts and applies the automotive qualification and temperature range. Soft saturation and low DCR are the two properties that matter on a 48 V or 12 V rail carrying tens of amps.

    At the rated 22.2 A the winding dissipates about 1.03 W in copper alone, using the typical DCR of 2.1 mOhm. That figure is the floor of the loss budget: it assumes the current is pure DC, and any ripple adds to it.

    Isat is specified as 20% rolloff @ +25 °C, so the number is a rolloff criterion rather than an absolute maximum. The useful working range extends a little beyond it on a soft saturation core, but the loop compensation has to be designed for the inductance that remains.

    Stored energy at Isat is about 44.1 uJ, which is the energy the inductor hands to the load during a transient before the control loop reacts.

    The K-factor of 1,764 converts inductance and ripple into flux swing: each amp of peak-to-peak ripple moves the core through about 353 Gauss of Bp-p, the figure the core-loss curve is plotted against.

    Where This Series Fits

    The HCMA family is the automotive high-current molded range, rated to +125 °C. It shares body sizes with the commercial HCM parts but is qualified and characterised for automotive use, with the current ratings to match the larger winding section.

    The HCMA0503 family spans 0.2 uH to 22 uH; this row sits at position 1 of 14.

    One step down the table, HCMA0503-R35-R, sits at 0.35 uH with 16.6 A and 3.9 mOhm – the lower inductance buys about 0 A of extra current in the same body.

    • Core material: iron powder core, 5.5 x 5.3 mm body at 3.0 mm.
    • Typical applications: body electronics; central body control module; vehicle access control system; headlamps, tail lamps and interior lighting; heating ventilation and air conditioning con­ trollers (hvac); doors, window lift and seat control.
    • Automotive derating practice: size against the saturation current at the hot corner and keep margin for the load transient, not just the steady-state current.

    Design Notes

    Copper resistance rises with temperature, so at the +125 °C limit the maximum DCR of 2.31 mOhm becomes roughly 3.26 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the AEC-Q200 grade covers the construction, not the thermal design of your board. The loss calculation is still the engineer’s job.

    • Compare against the commercial HCM row of the same size before substituting.
    • Check the current derating at the maximum ambient of the module.
    • Verify the shielding against the EMC plan for the board.

    Frequently Asked Questions

    Is this part suitable for a 48 V rail?
    The electrical ratings suit it, but isolation and creepage are board-level decisions. Check terminal spacing and any coating against the rail voltage.

    Is this part suitable for a 48 V rail?
    The electrical ratings suit it, but isolation and creepage are board-level decisions. Check terminal spacing and any coating against the rail voltage.

    How does this differ from the commercial HCM part?
    Same molded construction and similar body sizes, but automotive qualified, characterised to +125 °C, and wound for higher current in the larger sizes. The electrical rows are not interchangeable.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products