Eaton HCMA0703-2R2-R AEC-Q200 Inductor 2.2 uH, Isat 14 A
Eaton HCMA0703-2R2-R AEC-Q200 Inductor 2.2 uH, Isat 14 A

Eaton HCMA0703-2R2-R AEC-Q200 Inductor 2.2 uH, Isat 14 A

Share
Eaton HCMA0703-2R2-R: AEC-Q200 high-current inductor, 2.2 uH ±20%, 8 A Irms, Isat 14 A, DCR 18 mOhm, 7.4 x 7 mm.
    • Product Details
    • Download

    Eaton HCMA0703-2R2-R AEC-Q200 Inductor 2.2 uH, Isat 14 A

    HCMA0703-2R2-R at a glance: AEC-Q200 high-current inductor, 2.2 uH ±20%, 8 A Irms, Isat 14 A (20% rolloff @ +25 °C), DCR 18 mOhm, 7.4 x 7 mm.

    Specification Table

    ParameterValue
    Orderable part numberHCMA0703-2R2-R
    OCL (open circuit inductance)2.2 uH ±20%
    FLL minimum, at Isat1.32 uH
    Irms (DC, 40 °C rise)8 A
    Isat (20% rolloff @ +25 °C)14 A
    DCR typical @ +20 °C18 mOhm
    DCR maximum @ +20 °C20 mOhm
    K-factor (Bp-p = K x L x dI)281, Bp-p in Gauss
    Package7.4 x 7 mm
    Height3.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +125 °C (ambient plus self-heating)
    QualificationCommercial grade
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10282

    Mechanical Drawing

    HCMA0703-2R2-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10282: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    How to Read These Ratings

    This is the high-current member of the automotive molded family. Where the standard automotive parts top out at a few tens of amps, this one is built for the main DC-DC stage: thicker winding, larger body, and a saturation current that scales with it.

    Copper loss at the rated current works out to roughly 1.15 W from a typical DCR of 18 mOhm at 8 A. It is the number to start a thermal stack-up with, before core loss and before AC resistance rise.

    Saturation is quoted as 20% rolloff @ +25 °C. At that point the inductance has fallen to the stated fraction of its nominal value – the part is not damaged there, it simply stops behaving like the inductance on the label. Design the peak current to stay inside that boundary with margin for tolerance.

    Stored energy at Isat is about 216 uJ, which is the energy the inductor hands to the load during a transient before the control loop reacts.

    With K = 281, a peak-to-peak ripple of one amp produces roughly 618 Gauss of flux swing. Read the core-loss graph at that amplitude and at the switching frequency to get the core contribution to the total loss.

    Where This Series Fits

    The HCMA family is the automotive high-current molded range, rated to +125 °C. It shares body sizes with the commercial HCM parts but is qualified and characterised for automotive use, with the current ratings to match the larger winding section.

    Within the HCMA0703 family this is value 8 of 15, in a range that runs from 0.15 uH to 33 uH.

    The next value up in the same family, HCMA0703-3R3-R, gives 3.3 uH at 6 A and DCR 28 mOhm: the extra inductance costs about 3 A of rated current.

    • Core material: iron powder core, 7.4 x 7 mm body at 3.0 mm.
    • Typical applications: body electronics; central body control module; vehicle access control system; headlamps, tai lamps and interior lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control.
    • Automotive derating practice: size against the saturation current at the hot corner and keep margin for the load transient, not just the steady-state current.

    Sizing It Into a Design

    Copper resistance rises with temperature, so at the +125 °C limit the maximum DCR of 20 mOhm becomes roughly 28.3 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the AEC-Q200 grade covers the construction, not the thermal design of your board. The loss calculation is still the engineer’s job.

    • Size the saturation margin at the maximum ambient the module will see.
    • Confirm the terminal spacing against the rail voltage.
    • Check the terminal spacing against the rail voltage and the coating scheme.

    Frequently Asked Questions

    What current can it carry continuously?
    The Irms column, which is the DC current for the stated temperature rise without core loss. Continuous operation also depends on board copper and airflow, so the data sheet derating curves apply.

    Is it shielded?
    Yes – the winding is enclosed in the molded powder core, which keeps the external field low enough for dense automotive boards.

    Is it shielded?
    Yes – the winding is enclosed in the molded powder core, which keeps the external field low enough for dense automotive boards.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products