Eaton HCMA0703-330-R 33 uH Molded Automotive Inductor
Eaton HCMA0703-330-R 33 uH Molded Automotive Inductor

Eaton HCMA0703-330-R 33 uH Molded Automotive Inductor

Share
Eaton HCMA0703-330-R: AEC-Q200 high-current inductor, 33 uH ±20%, 1.8 A Irms, Isat 2.2 A, DCR 220 mOhm, 7.4 x 7 mm.
    • Product Details
    • Download

    Eaton HCMA0703-330-R 33 uH Molded Automotive Inductor

    HCMA0703-330-R at a glance: AEC-Q200 high-current inductor, 33 uH ±20%, 1.8 A Irms, Isat 2.2 A (20% rolloff @ +25 °C), DCR 220 mOhm, 7.4 x 7 mm.

    Electrical Specifications

    ParameterValue
    Orderable part numberHCMA0703-330-R
    OCL (open circuit inductance)33 uH ±20%
    FLL minimum, at Isat19.8 uH
    Irms (DC, 40 °C rise)1.8 A
    Isat (20% rolloff @ +25 °C)2.2 A
    DCR typical @ +20 °C220 mOhm
    DCR maximum @ +20 °C242 mOhm
    K-factor (Bp-p = K x L x dI)76, Bp-p in Gauss
    Package7.4 x 7 mm
    Height3.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +125 °C (ambient plus self-heating)
    QualificationCommercial grade
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10282

    Outline Drawing

    HCMA0703-330-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10282: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    How to Read These Ratings

    This is the high-current member of the automotive molded family. Where the standard automotive parts top out at a few tens of amps, this one is built for the main DC-DC stage: thicker winding, larger body, and a saturation current that scales with it.

    Copper loss at the rated current works out to roughly 0.713 W from a typical DCR of 220 mOhm at 1.8 A. It is the number to start a thermal stack-up with, before core loss and before AC resistance rise.

    Saturation is quoted as 20% rolloff @ +25 °C. At that point the inductance has fallen to the stated fraction of its nominal value – the part is not damaged there, it simply stops behaving like the inductance on the label. Design the peak current to stay inside that boundary with margin for tolerance.

    Energy storage at the saturation current is around 79.9 uJ, the number that connects the inductance and the current rating into a single transient figure.

    K-factor 76 means the flux swing is about 2,508 Gauss per amp of ripple. Core loss scales with the flux amplitude and the frequency, so this is the number to carry into the loss calculation rather than the inductance alone.

    Where This Series Fits

    The HCMA family is the automotive high-current molded range, rated to +125 °C. It shares body sizes with the commercial HCM parts but is qualified and characterised for automotive use, with the current ratings to match the larger winding section.

    Of the 15 values listed for HCMA0703, this is the 15th, in a family covering 0.15 uH to 33 uH.

    Compared with its neighbours in the table, HCMA0703-220-R trades 0 A of rated current for the next inductance step, which is the usual compromise in this family.

    • Core material: iron powder core, 7.4 x 7 mm body at 3.0 mm.
    • Typical applications: body electronics; central body control module; vehicle access control system; headlamps, tai lamps and interior lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control.
    • Automotive derating practice: size against the saturation current at the hot corner and keep margin for the load transient, not just the steady-state current.

    Putting It to Work

    Copper resistance rises with temperature, so at the +125 °C limit the maximum DCR of 242 mOhm becomes roughly 342 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the AEC-Q200 grade covers the construction, not the thermal design of your board. The loss calculation is still the engineer’s job.

    • Check the terminal spacing against the rail voltage and the coating scheme.
    • Check the terminal spacing against the rail voltage and the coating scheme.
    • Check the terminal spacing against the rail voltage and the coating scheme.

    Frequently Asked Questions

    Is it shielded?
    Yes – the winding is enclosed in the molded powder core, which keeps the external field low enough for dense automotive boards.

    Is this part suitable for a 48 V rail?
    The electrical ratings suit it, but isolation and creepage are board-level decisions. Check terminal spacing and any coating against the rail voltage.

    What is the difference between Irms and Isat here?
    Irms is the DC current for the rated temperature rise; Isat is the peak current at a defined inductance rolloff. A converter can exceed Irms briefly but must stay inside Isat.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products