Eaton HCMA0703-4R7-R 4.7 uH AEC-Q200 Inductor, 5.5 A
Eaton HCMA0703-4R7-R 4.7 uH AEC-Q200 Inductor, 5.5 A

Eaton HCMA0703-4R7-R 4.7 uH AEC-Q200 Inductor, 5.5 A

Share
Eaton HCMA0703-4R7-R: AEC-Q200 high-current inductor, 4.7 uH ±20%, 5.5 A Irms, Isat 10 A, DCR 37 mOhm, 7.4 x 7 mm.
    • Product Details
    • Download

    Eaton HCMA0703-4R7-R 4.7 uH AEC-Q200 Inductor, 5.5 A

    HCMA0703-4R7-R at a glance: AEC-Q200 high-current inductor, 4.7 uH ±20%, 5.5 A Irms, Isat 10 A (20% rolloff @ +25 °C), DCR 37 mOhm, 7.4 x 7 mm.

    Specification Table

    ParameterValue
    Orderable part numberHCMA0703-4R7-R
    OCL (open circuit inductance)4.7 uH ±20%
    FLL minimum, at Isat2.82 uH
    Irms (DC, 40 °C rise)5.5 A
    Isat (20% rolloff @ +25 °C)10 A
    DCR typical @ +20 °C37 mOhm
    DCR maximum @ +20 °C40 mOhm
    K-factor (Bp-p = K x L x dI)210, Bp-p in Gauss
    Package7.4 x 7 mm
    Height3.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +125 °C (ambient plus self-heating)
    QualificationCommercial grade
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10282

    Mechanical Drawing

    HCMA0703-4R7-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10282: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    The Figures Explained

    Molded powder core, shielded, AEC-Q200, +125 °C: the part is aimed at automotive DC-DC converters and motor-drive front ends where the inductor carries the full load current and the board has to pass EMC without a shield can.

    Copper loss at the rated current works out to roughly 1.12 W from a typical DCR of 37 mOhm at 5.5 A. It is the number to start a thermal stack-up with, before core loss and before AC resistance rise.

    The saturation rating reads 20% rolloff @ +25 °C. Treat it as the edge of the linear region: below it the inductance is within tolerance, above it the value droops. For a current-mode converter that means the peak current at the worst-case load step is what must fit under this number.

    The core stores roughly 235 uJ at the saturation point – a useful figure when sizing the output capacitance that has to absorb the same transient.

    The K-factor of 210 converts inductance and ripple into flux swing: each amp of peak-to-peak ripple moves the core through about 987 Gauss of Bp-p, the figure the core-loss curve is plotted against.

    What This Family Is For

    The HCMA family is the automotive high-current molded range, rated to +125 °C. It shares body sizes with the commercial HCM parts but is qualified and characterised for automotive use, with the current ratings to match the larger winding section.

    The HCMA0703 family spans 0.15 uH to 33 uH; this row sits at position 10 of 15.

    One step down the table, HCMA0703-3R3-R, sits at 3.3 uH with 6 A and 28 mOhm – the lower inductance buys about 1.5 A of extra current in the same body.

    • Core material: iron powder core, 7.4 x 7 mm body at 3.0 mm.
    • Typical applications: body electronics; central body control module; vehicle access control system; headlamps, tai lamps and interior lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control.
    • Automotive derating practice: size against the saturation current at the hot corner and keep margin for the load transient, not just the steady-state current.

    Sizing and Layout Notes

    Copper resistance rises with temperature, so at the +125 °C limit the maximum DCR of 40 mOhm becomes roughly 56.5 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the AEC-Q200 grade covers the construction, not the thermal design of your board. The loss calculation is still the engineer’s job.

    • Verify the shielding against the EMC plan for the board.
    • Check the terminal spacing against the rail voltage and the coating scheme.
    • Check the current derating at the maximum ambient of the module.

    Frequently Asked Questions

    Can it be used on a 48 V rail?
    The inductance and current ratings suit 48 V converters, but the insulation system and creepage are board-level concerns. Check the terminal spacing and conformal coating against the rail voltage.

    Is it shielded?
    Yes – the winding is enclosed in the molded powder core, which keeps the external field low enough for dense automotive boards.

    How does this differ from the commercial HCM part?
    Same molded construction and similar body sizes, but automotive qualified, characterised to +125 °C, and wound for higher current in the larger sizes. The electrical rows are not interchangeable.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products