Eaton HCMA0703-R15-R 0.15 uH Automotive High-Current Inductor
Eaton HCMA0703-R15-R 0.15 uH Automotive High-Current Inductor

Eaton HCMA0703-R15-R 0.15 uH Automotive High-Current Inductor

Share
Eaton HCMA0703-R15-R: AEC-Q200 high-current inductor, 0.15 uH ±20%, 26 A Irms, Isat 52 A, DCR 1.9 mOhm, 7.4 x 7 mm.
    • Product Details
    • Download

    Eaton HCMA0703-R15-R 0.15 uH Automotive High-Current Inductor

    HCMA0703-R15-R at a glance: AEC-Q200 high-current inductor, 0.15 uH ±20%, 26 A Irms, Isat 52 A (20% rolloff @ +25 °C), DCR 1.9 mOhm, 7.4 x 7 mm.

    Key Specifications

    ParameterValue
    Orderable part numberHCMA0703-R15-R
    OCL (open circuit inductance)0.15 uH ±20%
    FLL minimum, at Isat0.09 uH
    Irms (DC, 40 °C rise)26 A
    Isat (20% rolloff @ +25 °C)52 A
    DCR typical @ +20 °C1.9 mOhm
    DCR maximum @ +20 °C2.5 mOhm
    K-factor (Bp-p = K x L x dI)1,044, Bp-p in Gauss
    Package7.4 x 7 mm
    Height3.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +125 °C (ambient plus self-heating)
    QualificationCommercial grade
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10282

    Mechanical Dimensions & Pad Layout

    HCMA0703-R15-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10282: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    What the Numbers Mean

    AEC-Q200 qualified high-current inductor on a molded powder core, rated to +125 °C. The construction is chosen for current density: the winding is pressed into the magnetic material, so there is no bobbin wasting window area and the DCR stays low for the body size.

    The DCR figure of 1.9 mOhm is what sets the efficiency: at 26 A the winding drops about 0.049 mV and dissipates 1.28 W. On a low-voltage rail that drop is a measurable fraction of the output, so the DCR column deserves as much attention as the inductance.

    The Isat column is 20% rolloff @ +25 °C. Note what it does and does not mean: it is a defined rolloff point, not a destruction limit. Above it the inductance continues to fall, which is why the transient peak current should be checked against the curve, not just against the number.

    Stored energy at Isat is about 203 uJ, which is the energy the inductor hands to the load during a transient before the control loop reacts.

    The K-factor of 1,044 converts inductance and ripple into flux swing: each amp of peak-to-peak ripple moves the core through about 157 Gauss of Bp-p, the figure the core-loss curve is plotted against.

    Positioning in the Range

    The HCMA family is the automotive high-current molded range, rated to +125 °C. It shares body sizes with the commercial HCM parts but is qualified and characterised for automotive use, with the current ratings to match the larger winding section.

    Within the HCMA0703 family this is value 1 of 15, in a range that runs from 0.15 uH to 33 uH.

    The next value up in the same family, HCMA0703-R22-R, gives 0.22 uH at 23 A and DCR 2.5 mOhm: the extra inductance costs about 0 A of rated current.

    • Core material: iron powder core, 7.4 x 7 mm body at 3.0 mm.
    • Typical applications: body electronics; central body control module; vehicle access control system; headlamps, tai lamps and interior lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control.
    • Automotive derating practice: size against the saturation current at the hot corner and keep margin for the load transient, not just the steady-state current.

    Sizing It Into a Design

    Copper resistance rises with temperature, so at the +125 °C limit the maximum DCR of 2.5 mOhm becomes roughly 3.53 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the AEC-Q200 grade covers the construction, not the thermal design of your board. The loss calculation is still the engineer’s job.

    • Check the current derating at the maximum ambient of the module.
    • Compare against the commercial HCM row of the same size before substituting.
    • Compare against the commercial HCM row of the same size before substituting.

    Frequently Asked Questions

    How does this differ from the commercial HCM part?
    Same molded construction and similar body sizes, but automotive qualified, characterised to +125 °C, and wound for higher current in the larger sizes. The electrical rows are not interchangeable.

    Can it be used on a 48 V rail?
    The inductance and current ratings suit 48 V converters, but the insulation system and creepage are board-level concerns. Check the terminal spacing and conformal coating against the rail voltage.

    How does this differ from the commercial HCM part?
    Same molded construction and similar body sizes, but automotive qualified, characterised to +125 °C, and wound for higher current in the larger sizes. The electrical rows are not interchangeable.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products