Eaton HCMA0703-R47-R 0.47 uH Molded Automotive Inductor
Eaton HCMA0703-R47-R 0.47 uH Molded Automotive Inductor

Eaton HCMA0703-R47-R 0.47 uH Molded Automotive Inductor

Share
Eaton HCMA0703-R47-R: AEC-Q200 high-current inductor, 0.47 uH ±20%, 17.5 A Irms, Isat 26 A, DCR 4 mOhm, 7.4 x 7 mm.
    • Product Details
    • Download

    Eaton HCMA0703-R47-R 0.47 uH Molded Automotive Inductor

    HCMA0703-R47-R at a glance: AEC-Q200 high-current inductor, 0.47 uH ±20%, 17.5 A Irms, Isat 26 A (20% rolloff @ +25 °C), DCR 4 mOhm, 7.4 x 7 mm.

    Key Specifications

    ParameterValue
    Orderable part numberHCMA0703-R47-R
    OCL (open circuit inductance)0.47 uH ±20%
    FLL minimum, at Isat0.28 uH
    Irms (DC, 40 °C rise)17.5 A
    Isat (20% rolloff @ +25 °C)26 A
    DCR typical @ +20 °C4 mOhm
    DCR maximum @ +20 °C4.2 mOhm
    K-factor (Bp-p = K x L x dI)580, Bp-p in Gauss
    Package7.4 x 7 mm
    Height3.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +125 °C (ambient plus self-heating)
    QualificationCommercial grade
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10282

    Mechanical Drawing

    HCMA0703-R47-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10282: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    The Figures Explained

    The family takes the molded construction used on the commercial high-current parts and applies the automotive qualification and temperature range. Soft saturation and low DCR are the two properties that matter on a 48 V or 12 V rail carrying tens of amps.

    Copper loss at the rated current works out to roughly 1.23 W from a typical DCR of 4 mOhm at 17.5 A. It is the number to start a thermal stack-up with, before core loss and before AC resistance rise.

    Isat is specified as 20% rolloff @ +25 °C, so the number is a rolloff criterion rather than an absolute maximum. The useful working range extends a little beyond it on a soft saturation core, but the loop compensation has to be designed for the inductance that remains.

    The core stores roughly 159 uJ at the saturation point – a useful figure when sizing the output capacitance that has to absorb the same transient.

    K-factor 580 means the flux swing is about 273 Gauss per amp of ripple. Core loss scales with the flux amplitude and the frequency, so this is the number to carry into the loss calculation rather than the inductance alone.

    Where This Series Fits

    The HCMA family is the automotive high-current molded range, rated to +125 °C. It shares body sizes with the commercial HCM parts but is qualified and characterised for automotive use, with the current ratings to match the larger winding section.

    The HCMA0703 family spans 0.15 uH to 33 uH; this row sits at position 3 of 15.

    Compared with its neighbours in the table, HCMA0703-R68-R trades 7.5 A of rated current for the next inductance step, which is the usual compromise in this family.

    • Core material: iron powder core, 7.4 x 7 mm body at 3.0 mm.
    • Typical applications: body electronics; central body control module; vehicle access control system; headlamps, tai lamps and interior lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control.
    • Automotive derating practice: size against the saturation current at the hot corner and keep margin for the load transient, not just the steady-state current.

    Sizing and Layout Notes

    Copper resistance rises with temperature, so at the +125 °C limit the maximum DCR of 4.2 mOhm becomes roughly 5.93 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the AEC-Q200 grade covers the construction, not the thermal design of your board. The loss calculation is still the engineer’s job.

    • Check the terminal spacing against the rail voltage and the coating scheme.
    • Size the saturation margin at the maximum ambient the module will see.
    • Compare against the commercial HCM row of the same size before substituting.

    Frequently Asked Questions

    How does this differ from the commercial HCM part?
    Same molded construction and similar body sizes, but automotive qualified, characterised to +125 °C, and wound for higher current in the larger sizes. The electrical rows are not interchangeable.

    Is this part suitable for a 48 V rail?
    The electrical ratings suit it, but isolation and creepage are board-level decisions. Check terminal spacing and any coating against the rail voltage.

    Is this part suitable for a 48 V rail?
    The electrical ratings suit it, but isolation and creepage are board-level decisions. Check terminal spacing and any coating against the rail voltage.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products