Eaton HCMA0703-R82-R 0.82 uH Automotive High-Current Inductor
Eaton HCMA0703-R82-R 0.82 uH Automotive High-Current Inductor

Eaton HCMA0703-R82-R 0.82 uH Automotive High-Current Inductor

Share
Eaton HCMA0703-R82-R: AEC-Q200 high-current inductor, 0.82 uH ±20%, 13 A Irms, Isat 24 A, DCR 6.7 mOhm, 7.4 x 7 mm.
    • Product Details
    • Download

    Eaton HCMA0703-R82-R 0.82 uH Automotive High-Current Inductor

    HCMA0703-R82-R at a glance: AEC-Q200 high-current inductor, 0.82 uH ±20%, 13 A Irms, Isat 24 A (20% rolloff @ +25 °C), DCR 6.7 mOhm, 7.4 x 7 mm.

    Electrical Specifications

    ParameterValue
    Orderable part numberHCMA0703-R82-R
    OCL (open circuit inductance)0.82 uH ±20%
    FLL minimum, at Isat0.49 uH
    Irms (DC, 40 °C rise)13 A
    Isat (20% rolloff @ +25 °C)24 A
    DCR typical @ +20 °C6.7 mOhm
    DCR maximum @ +20 °C8 mOhm
    K-factor (Bp-p = K x L x dI)439, Bp-p in Gauss
    Package7.4 x 7 mm
    Height3.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +125 °C (ambient plus self-heating)
    QualificationCommercial grade
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10282

    Mechanical Dimensions & Pad Layout

    HCMA0703-R82-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10282: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    Reading the Data Sheet

    Molded powder core, shielded, AEC-Q200, +125 °C: the part is aimed at automotive DC-DC converters and motor-drive front ends where the inductor carries the full load current and the board has to pass EMC without a shield can.

    The DCR figure of 6.7 mOhm is what sets the efficiency: at 13 A the winding drops about 0.087 mV and dissipates 1.13 W. On a low-voltage rail that drop is a measurable fraction of the output, so the DCR column deserves as much attention as the inductance.

    Isat is specified as 20% rolloff @ +25 °C, so the number is a rolloff criterion rather than an absolute maximum. The useful working range extends a little beyond it on a soft saturation core, but the loop compensation has to be designed for the inductance that remains.

    Stored energy at Isat is about 236 uJ, which is the energy the inductor hands to the load during a transient before the control loop reacts.

    K-factor 439 means the flux swing is about 360 Gauss per amp of ripple. Core loss scales with the flux amplitude and the frequency, so this is the number to carry into the loss calculation rather than the inductance alone.

    Series Positioning

    The HCMA family is the automotive high-current molded range, rated to +125 °C. It shares body sizes with the commercial HCM parts but is qualified and characterised for automotive use, with the current ratings to match the larger winding section.

    The HCMA0703 family spans 0.15 uH to 33 uH; this row sits at position 5 of 15.

    The next value up in the same family, HCMA0703-1R0-R, gives 1.0 uH at 11 A and DCR 9 mOhm: the extra inductance costs about 4.5 A of rated current.

    • Core material: iron powder core, 7.4 x 7 mm body at 3.0 mm.
    • Typical applications: body electronics; central body control module; vehicle access control system; headlamps, tai lamps and interior lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control.
    • Automotive derating practice: size against the saturation current at the hot corner and keep margin for the load transient, not just the steady-state current.

    Design Notes

    Copper resistance rises with temperature, so at the +125 °C limit the maximum DCR of 8 mOhm becomes roughly 11.3 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the AEC-Q200 grade covers the construction, not the thermal design of your board. The loss calculation is still the engineer’s job.

    • Confirm the terminal spacing against the rail voltage.
    • Compare against the commercial HCM row of the same size before substituting.
    • Size the saturation margin at the maximum ambient the module will see.

    Frequently Asked Questions

    Is this part suitable for a 48 V rail?
    The electrical ratings suit it, but isolation and creepage are board-level decisions. Check terminal spacing and any coating against the rail voltage.

    Can it be used on a 48 V rail?
    The inductance and current ratings suit 48 V converters, but the insulation system and creepage are board-level concerns. Check the terminal spacing and conformal coating against the rail voltage.

    Is this part suitable for a 48 V rail?
    The electrical ratings suit it, but isolation and creepage are board-level decisions. Check terminal spacing and any coating against the rail voltage.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products