Eaton HCMA1104-4R7-R 4.7 uH AEC-Q200 Inductor, 8.5 A
Eaton HCMA1104-4R7-R 4.7 uH AEC-Q200 Inductor, 8.5 A

Eaton HCMA1104-4R7-R 4.7 uH AEC-Q200 Inductor, 8.5 A

Share
Eaton HCMA1104-4R7-R: AEC-Q200 high-current inductor, 4.7 uH ±20%, 8.5 A Irms, Isat 15 A, DCR 17 mOhm, 11.5 x 10.3 mm.
    • Product Details
    • Download

    Eaton HCMA1104-4R7-R 4.7 uH AEC-Q200 Inductor, 8.5 A

    HCMA1104-4R7-R at a glance: AEC-Q200 high-current inductor, 4.7 uH ±20%, 8.5 A Irms, Isat 15 A (20% rolloff @ +25 °C), DCR 17 mOhm, 11.5 x 10.3 mm.

    Specification Table

    ParameterValue
    Orderable part numberHCMA1104-4R7-R
    OCL (open circuit inductance)4.7 uH ±20%
    FLL minimum, at Isat2.63 uH
    Irms (DC, 40 °C rise)8.5 A
    Isat (20% rolloff @ +25 °C)15 A
    DCR typical @ +20 °C17 mOhm
    DCR maximum @ +20 °C20 mOhm
    K-factor (Bp-p = K x L x dI)175, Bp-p in Gauss
    Package11.5 x 10.3 mm
    Height4.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +125 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10349

    Mechanical Drawing

    HCMA1104-4R7-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10349: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    Reading the Data Sheet

    Molded powder core, shielded, AEC-Q200, +125 °C: the part is aimed at automotive DC-DC converters and motor-drive front ends where the inductor carries the full load current and the board has to pass EMC without a shield can.

    At the rated 8.5 A the winding dissipates about 1.23 W in copper alone, using the typical DCR of 17 mOhm. That figure is the floor of the loss budget: it assumes the current is pure DC, and any ripple adds to it.

    The saturation rating reads 20% rolloff @ +25 °C. Treat it as the edge of the linear region: below it the inductance is within tolerance, above it the value droops. For a current-mode converter that means the peak current at the worst-case load step is what must fit under this number.

    The core stores roughly 529 uJ at the saturation point – a useful figure when sizing the output capacitance that has to absorb the same transient.

    The K-factor of 175 converts inductance and ripple into flux swing: each amp of peak-to-peak ripple moves the core through about 822 Gauss of Bp-p, the figure the core-loss curve is plotted against.

    What This Family Is For

    The HCMA family is the automotive high-current molded range, rated to +125 °C. It shares body sizes with the commercial HCM parts but is qualified and characterised for automotive use, with the current ratings to match the larger winding section.

    Within the HCMA1104 family this is value 10 of 12, in a range that runs from 0.2 uH to 22 uH.

    Compared with its neighbours in the table, HCMA1104-100-R trades 2.5 A of rated current for the next inductance step, which is the usual compromise in this family.

    • Core material: iron powder core, 11.5 x 10.3 mm body at 4.0 mm.
    • Typical applications: body electronics; central body control module; vehicle access control system; headlamps, tai lamps and interior lighting; heating ventilation and air conditioning con- trollers (hvac); doors, window lift and seat control.
    • Automotive derating practice: size against the saturation current at the hot corner and keep margin for the load transient, not just the steady-state current.

    Sizing and Layout Notes

    Copper resistance rises with temperature, so at the +125 °C limit the maximum DCR of 20 mOhm becomes roughly 28.3 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the AEC-Q200 grade covers the construction, not the thermal design of your board. The loss calculation is still the engineer’s job.

    • Size the saturation margin at the maximum ambient the module will see.
    • Confirm the terminal spacing against the rail voltage.
    • Check the current derating at the maximum ambient of the module.

    Frequently Asked Questions

    What current can it carry continuously?
    The Irms column, which is the DC current for the stated temperature rise without core loss. Continuous operation also depends on board copper and airflow, so the data sheet derating curves apply.

    Is it shielded?
    Yes – the winding is enclosed in the molded powder core, which keeps the external field low enough for dense automotive boards.

    How does this differ from the commercial HCM part?
    Same molded construction and similar body sizes, but automotive qualified, characterised to +125 °C, and wound for higher current in the larger sizes. The electrical rows are not interchangeable.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products