Eaton HCMA1305-1R5-R AEC-Q200 Inductor 1.50 uH, Isat 48 A
Eaton HCMA1305-1R5-R AEC-Q200 Inductor 1.50 uH, Isat 48 A

Eaton HCMA1305-1R5-R AEC-Q200 Inductor 1.50 uH, Isat 48 A

Share
Eaton HCMA1305-1R5-R: AEC-Q200 high-current inductor, 1.50 uH ±20%, 23 A Irms, Isat 48 A, DCR 2.75 mOhm, 13.8 x 12.5 mm.
    • Product Details
    • Download

    Eaton HCMA1305-1R5-R AEC-Q200 Inductor 1.50 uH, Isat 48 A

    HCMA1305-1R5-R at a glance: AEC-Q200 high-current inductor, 1.50 uH ±20%, 23 A Irms, Isat 48 A (20% rolloff @ +25 °C), DCR 2.75 mOhm, 13.8 x 12.5 mm.

    Key Specifications

    ParameterValue
    Orderable part numberHCMA1305-1R5-R
    OCL (open circuit inductance)1.50 uH ±20%
    FLL minimum, at Isat0.96 uH
    Irms (DC, 40 °C rise)23 A
    Isat (20% rolloff @ +25 °C)48 A
    DCR typical @ +20 °C2.75 mOhm
    DCR maximum @ +20 °C3.16 mOhm
    K-factor (Bp-p = K x L x dI)225, Bp-p in Gauss
    Package13.8 x 12.5 mm
    Height5.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +125 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10277

    Mechanical Dimensions & Pad Layout

    HCMA1305-1R5-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10277: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    The Figures Explained

    Molded powder core, shielded, AEC-Q200, +125 °C: the part is aimed at automotive DC-DC converters and motor-drive front ends where the inductor carries the full load current and the board has to pass EMC without a shield can.

    Copper loss at the rated current works out to roughly 1.46 W from a typical DCR of 2.75 mOhm at 23 A. It is the number to start a thermal stack-up with, before core loss and before AC resistance rise.

    Saturation is quoted as 20% rolloff @ +25 °C. At that point the inductance has fallen to the stated fraction of its nominal value – the part is not damaged there, it simply stops behaving like the inductance on the label. Design the peak current to stay inside that boundary with margin for tolerance.

    Stored energy at Isat is about 1,728 uJ, which is the energy the inductor hands to the load during a transient before the control loop reacts.

    With K = 225, a peak-to-peak ripple of one amp produces roughly 338 Gauss of flux swing. Read the core-loss graph at that amplitude and at the switching frequency to get the core contribution to the total loss.

    Where This Series Fits

    The HCMA family is the automotive high-current molded range, rated to +125 °C. It shares body sizes with the commercial HCM parts but is qualified and characterised for automotive use, with the current ratings to match the larger winding section.

    In the HCMA1305 line-up this part is number 9 of 21 by inductance, between 0.1 uH and 33 uH.

    One step down the table, HCMA1305-1R0-R, sits at 1.00 uH with 29 A and 2.1 mOhm – the lower inductance buys about 8 A of extra current in the same body.

    • Core material: iron powder core, 13.8 x 12.5 mm body at 5.0 mm.
    • Typical applications: body electronics; central body control module; vehicle access control system; headlamps, tail lamps and interior lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control.
    • Automotive derating practice: size against the saturation current at the hot corner and keep margin for the load transient, not just the steady-state current.

    Sizing It Into a Design

    Copper resistance rises with temperature, so at the +125 °C limit the maximum DCR of 3.16 mOhm becomes roughly 4.46 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the AEC-Q200 grade covers the construction, not the thermal design of your board. The loss calculation is still the engineer’s job.

    • Check the terminal spacing against the rail voltage and the coating scheme.
    • Compare against the commercial HCM row of the same size before substituting.
    • Check the current derating at the maximum ambient of the module.

    Frequently Asked Questions

    Is it shielded?
    Yes – the winding is enclosed in the molded powder core, which keeps the external field low enough for dense automotive boards.

    Is it shielded?
    Yes – the winding is enclosed in the molded powder core, which keeps the external field low enough for dense automotive boards.

    Is it shielded?
    Yes – the winding is enclosed in the molded powder core, which keeps the external field low enough for dense automotive boards.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products