Eaton HCMA1305-1R8-R 1.80 uH Automotive High-Current Inductor
Eaton HCMA1305-1R8-R 1.80 uH Automotive High-Current Inductor

Eaton HCMA1305-1R8-R 1.80 uH Automotive High-Current Inductor

Share
Eaton HCMA1305-1R8-R: AEC-Q200 high-current inductor, 1.80 uH ±20%, 21 A Irms, Isat 40 A, DCR 4 mOhm, 13.8 x 12.5 mm.
    • Product Details
    • Download

    Eaton HCMA1305-1R8-R 1.80 uH Automotive High-Current Inductor

    HCMA1305-1R8-R at a glance: AEC-Q200 high-current inductor, 1.80 uH ±20%, 21 A Irms, Isat 40 A (20% rolloff @ +25 °C), DCR 4 mOhm, 13.8 x 12.5 mm.

    Specification Table

    ParameterValue
    Orderable part numberHCMA1305-1R8-R
    OCL (open circuit inductance)1.80 uH ±20%
    FLL minimum, at Isat1.15 uH
    Irms (DC, 40 °C rise)21 A
    Isat (20% rolloff @ +25 °C)40 A
    DCR typical @ +20 °C4 mOhm
    DCR maximum @ +20 °C4.6 mOhm
    K-factor (Bp-p = K x L x dI)216, Bp-p in Gauss
    Package13.8 x 12.5 mm
    Height5.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +125 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10277

    Dimensions and Pad Layout

    HCMA1305-1R8-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10277: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    What the Numbers Mean

    AEC-Q200 qualified high-current inductor on a molded powder core, rated to +125 °C. The construction is chosen for current density: the winding is pressed into the magnetic material, so there is no bobbin wasting window area and the DCR stays low for the body size.

    At the rated 21 A the winding dissipates about 1.76 W in copper alone, using the typical DCR of 4 mOhm. That figure is the floor of the loss budget: it assumes the current is pure DC, and any ripple adds to it.

    The saturation rating reads 20% rolloff @ +25 °C. Treat it as the edge of the linear region: below it the inductance is within tolerance, above it the value droops. For a current-mode converter that means the peak current at the worst-case load step is what must fit under this number.

    At Isat the part holds about 1,440 uJ. On a multiphase rail that is the energy per phase available to bridge a load step, which sets how much bulk capacitance the controller still needs.

    With K = 216, a peak-to-peak ripple of one amp produces roughly 389 Gauss of flux swing. Read the core-loss graph at that amplitude and at the switching frequency to get the core contribution to the total loss.

    What This Family Is For

    The HCMA family is the automotive high-current molded range, rated to +125 °C. It shares body sizes with the commercial HCM parts but is qualified and characterised for automotive use, with the current ratings to match the larger winding section.

    Within the HCMA1305 family this is value 10 of 21, in a range that runs from 0.1 uH to 33 uH.

    One step down the table, HCMA1305-1R5-R, sits at 1.50 uH with 23 A and 2.75 mOhm – the lower inductance buys about 3 A of extra current in the same body.

    • Core material: iron powder core, 13.8 x 12.5 mm body at 5.0 mm.
    • Typical applications: body electronics; central body control module; vehicle access control system; headlamps, tail lamps and interior lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control.
    • Automotive derating practice: size against the saturation current at the hot corner and keep margin for the load transient, not just the steady-state current.

    Design Notes

    Copper resistance rises with temperature, so at the +125 °C limit the maximum DCR of 4.6 mOhm becomes roughly 6.5 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the AEC-Q200 grade covers the construction, not the thermal design of your board. The loss calculation is still the engineer’s job.

    • Size the saturation margin at the maximum ambient the module will see.
    • Size the saturation margin at the maximum ambient the module will see.
    • Check the current derating at the maximum ambient of the module.

    Frequently Asked Questions

    What current can it carry continuously?
    The Irms column, which is the DC current for the stated temperature rise without core loss. Continuous operation also depends on board copper and airflow, so the data sheet derating curves apply.

    How does this differ from the commercial HCM part?
    Same molded construction and similar body sizes, but automotive qualified, characterised to +125 °C, and wound for higher current in the larger sizes. The electrical rows are not interchangeable.

    Can it be used on a 48 V rail?
    The inductance and current ratings suit 48 V converters, but the insulation system and creepage are board-level concerns. Check the terminal spacing and conformal coating against the rail voltage.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products