Eaton HCMA1305-220-R 22.0 uH Molded Automotive Inductor
Eaton HCMA1305-220-R 22.0 uH Molded Automotive Inductor

Eaton HCMA1305-220-R 22.0 uH Molded Automotive Inductor

Share
Eaton HCMA1305-220-R: AEC-Q200 high-current inductor, 22.0 uH ±20%, 6.2 A Irms, Isat 10 A, DCR 45 mOhm, 13.8 x 12.5 mm.
    • Product Details
    • Download

    Eaton HCMA1305-220-R 22.0 uH Molded Automotive Inductor

    HCMA1305-220-R at a glance: AEC-Q200 high-current inductor, 22.0 uH ±20%, 6.2 A Irms, Isat 10 A (20% rolloff @ +25 °C), DCR 45 mOhm, 13.8 x 12.5 mm.

    Electrical Specifications

    ParameterValue
    Orderable part numberHCMA1305-220-R
    OCL (open circuit inductance)22.0 uH ±20%
    FLL minimum, at Isat14.1 uH
    Irms (DC, 40 °C rise)6.2 A
    Isat (20% rolloff @ +25 °C)10 A
    DCR typical @ +20 °C45 mOhm
    DCR maximum @ +20 °C51.8 mOhm
    K-factor (Bp-p = K x L x dI)63, Bp-p in Gauss
    Package13.8 x 12.5 mm
    Height5.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +125 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10277

    Mechanical Dimensions & Pad Layout

    HCMA1305-220-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10277: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    Reading the Data Sheet

    Molded powder core, shielded, AEC-Q200, +125 °C: the part is aimed at automotive DC-DC converters and motor-drive front ends where the inductor carries the full load current and the board has to pass EMC without a shield can.

    The DCR figure of 45 mOhm is what sets the efficiency: at 6.2 A the winding drops about 0.279 mV and dissipates 1.73 W. On a low-voltage rail that drop is a measurable fraction of the output, so the DCR column deserves as much attention as the inductance.

    Isat is specified as 20% rolloff @ +25 °C, so the number is a rolloff criterion rather than an absolute maximum. The useful working range extends a little beyond it on a soft saturation core, but the loop compensation has to be designed for the inductance that remains.

    Stored energy at Isat is about 1,100 uJ, which is the energy the inductor hands to the load during a transient before the control loop reacts.

    With K = 63, a peak-to-peak ripple of one amp produces roughly 1,386 Gauss of flux swing. Read the core-loss graph at that amplitude and at the switching frequency to get the core contribution to the total loss.

    Series Positioning

    The HCMA family is the automotive high-current molded range, rated to +125 °C. It shares body sizes with the commercial HCM parts but is qualified and characterised for automotive use, with the current ratings to match the larger winding section.

    Within the HCMA1305 family this is value 20 of 21, in a range that runs from 0.1 uH to 33 uH.

    One step down the table, HCMA1305-150-R, sits at 15.0 uH with 7.7 A and 29 mOhm – the lower inductance buys about 2.5 A of extra current in the same body.

    • Core material: iron powder core, 13.8 x 12.5 mm body at 5.0 mm.
    • Typical applications: body electronics; central body control module; vehicle access control system; headlamps, tail lamps and interior lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control.
    • Automotive derating practice: size against the saturation current at the hot corner and keep margin for the load transient, not just the steady-state current.

    Design Notes

    Copper resistance rises with temperature, so at the +125 °C limit the maximum DCR of 51.8 mOhm becomes roughly 73.2 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the AEC-Q200 grade covers the construction, not the thermal design of your board. The loss calculation is still the engineer’s job.

    • Verify the shielding against the EMC plan for the board.
    • Verify the shielding against the EMC plan for the board.
    • Check the terminal spacing against the rail voltage and the coating scheme.

    Frequently Asked Questions

    Is it shielded?
    Yes – the winding is enclosed in the molded powder core, which keeps the external field low enough for dense automotive boards.

    What current can it carry continuously?
    The Irms column, which is the DC current for the stated temperature rise without core loss. Continuous operation also depends on board copper and airflow, so the data sheet derating curves apply.

    Is it shielded?
    Yes – the winding is enclosed in the molded powder core, which keeps the external field low enough for dense automotive boards.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products