Eaton HCMA1305-330-R AEC-Q200 Inductor 33.0 uH, Isat 8 A
Eaton HCMA1305-330-R AEC-Q200 Inductor 33.0 uH, Isat 8 A

Eaton HCMA1305-330-R AEC-Q200 Inductor 33.0 uH, Isat 8 A

Share
Eaton HCMA1305-330-R: AEC-Q200 high-current inductor, 33.0 uH ±20%, 5.2 A Irms, Isat 8 A, DCR 74.5 mOhm, 13.8 x 12.5 mm.
    • Product Details
    • Download

    Eaton HCMA1305-330-R AEC-Q200 Inductor 33.0 uH, Isat 8 A

    HCMA1305-330-R at a glance: AEC-Q200 high-current inductor, 33.0 uH ±20%, 5.2 A Irms, Isat 8 A (20% rolloff @ +25 °C), DCR 74.5 mOhm, 13.8 x 12.5 mm.

    Specification Table

    ParameterValue
    Orderable part numberHCMA1305-330-R
    OCL (open circuit inductance)33.0 uH ±20%
    FLL minimum, at Isat21.1 uH
    Irms (DC, 40 °C rise)5.2 A
    Isat (20% rolloff @ +25 °C)8 A
    DCR typical @ +20 °C74.5 mOhm
    DCR maximum @ +20 °C85.5 mOhm
    K-factor (Bp-p = K x L x dI)48, Bp-p in Gauss
    Package13.8 x 12.5 mm
    Height5.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +125 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10277

    Mechanical Dimensions & Pad Layout

    HCMA1305-330-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10277: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    What the Numbers Mean

    AEC-Q200 qualified high-current inductor on a molded powder core, rated to +125 °C. The construction is chosen for current density: the winding is pressed into the magnetic material, so there is no bobbin wasting window area and the DCR stays low for the body size.

    The DCR figure of 74.5 mOhm is what sets the efficiency: at 5.2 A the winding drops about 0.387 mV and dissipates 2.01 W. On a low-voltage rail that drop is a measurable fraction of the output, so the DCR column deserves as much attention as the inductance.

    Isat is specified as 20% rolloff @ +25 °C, so the number is a rolloff criterion rather than an absolute maximum. The useful working range extends a little beyond it on a soft saturation core, but the loop compensation has to be designed for the inductance that remains.

    The core stores roughly 1,056 uJ at the saturation point – a useful figure when sizing the output capacitance that has to absorb the same transient.

    With K = 48, a peak-to-peak ripple of one amp produces roughly 1,584 Gauss of flux swing. Read the core-loss graph at that amplitude and at the switching frequency to get the core contribution to the total loss.

    Series Positioning

    The HCMA family is the automotive high-current molded range, rated to +125 °C. It shares body sizes with the commercial HCM parts but is qualified and characterised for automotive use, with the current ratings to match the larger winding section.

    The HCMA1305 family spans 0.1 uH to 33 uH; this row sits at position 21 of 21.

    The next value up in the same family, HCMA1305-220-R, gives 22.0 uH at 6.2 A and DCR 45 mOhm: the extra inductance costs about 0 A of rated current.

    • Core material: iron powder core, 13.8 x 12.5 mm body at 5.0 mm.
    • Typical applications: body electronics; central body control module; vehicle access control system; headlamps, tail lamps and interior lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control.
    • Automotive derating practice: size against the saturation current at the hot corner and keep margin for the load transient, not just the steady-state current.

    Sizing and Layout Notes

    Copper resistance rises with temperature, so at the +125 °C limit the maximum DCR of 85.5 mOhm becomes roughly 121 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the AEC-Q200 grade covers the construction, not the thermal design of your board. The loss calculation is still the engineer’s job.

    • Compare against the commercial HCM row of the same size before substituting.
    • Size the saturation margin at the maximum ambient the module will see.
    • Check the current derating at the maximum ambient of the module.

    Frequently Asked Questions

    What current can it carry continuously?
    The Irms column, which is the DC current for the stated temperature rise without core loss. Continuous operation also depends on board copper and airflow, so the data sheet derating curves apply.

    Can it be used on a 48 V rail?
    The inductance and current ratings suit 48 V converters, but the insulation system and creepage are board-level concerns. Check the terminal spacing and conformal coating against the rail voltage.

    Is it shielded?
    Yes – the winding is enclosed in the molded powder core, which keeps the external field low enough for dense automotive boards.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products