Eaton HCMA1305-4R7-R AEC-Q200 Inductor 4.70 uH, Isat 27 A
Eaton HCMA1305-4R7-R AEC-Q200 Inductor 4.70 uH, Isat 27 A

Eaton HCMA1305-4R7-R AEC-Q200 Inductor 4.70 uH, Isat 27 A

Share
Eaton HCMA1305-4R7-R: AEC-Q200 high-current inductor, 4.70 uH ±20%, 12 A Irms, Isat 27 A, DCR 11 mOhm, 13.8 x 12.5 mm.
    • Product Details
    • Download

    Eaton HCMA1305-4R7-R AEC-Q200 Inductor 4.70 uH, Isat 27 A

    HCMA1305-4R7-R at a glance: AEC-Q200 high-current inductor, 4.70 uH ±20%, 12 A Irms, Isat 27 A (20% rolloff @ +25 °C), DCR 11 mOhm, 13.8 x 12.5 mm.

    Electrical Specifications

    ParameterValue
    Orderable part numberHCMA1305-4R7-R
    OCL (open circuit inductance)4.70 uH ±20%
    FLL minimum, at Isat3.01 uH
    Irms (DC, 40 °C rise)12 A
    Isat (20% rolloff @ +25 °C)27 A
    DCR typical @ +20 °C11 mOhm
    DCR maximum @ +20 °C12.7 mOhm
    K-factor (Bp-p = K x L x dI)161, Bp-p in Gauss
    Package13.8 x 12.5 mm
    Height5.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +125 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10277

    Mechanical Dimensions & Pad Layout

    HCMA1305-4R7-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10277: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    Reading the Data Sheet

    Molded powder core, shielded, AEC-Q200, +125 °C: the part is aimed at automotive DC-DC converters and motor-drive front ends where the inductor carries the full load current and the board has to pass EMC without a shield can.

    At the rated 12 A the winding dissipates about 1.58 W in copper alone, using the typical DCR of 11 mOhm. That figure is the floor of the loss budget: it assumes the current is pure DC, and any ripple adds to it.

    The saturation rating reads 20% rolloff @ +25 °C. Treat it as the edge of the linear region: below it the inductance is within tolerance, above it the value droops. For a current-mode converter that means the peak current at the worst-case load step is what must fit under this number.

    The core stores roughly 1,713 uJ at the saturation point – a useful figure when sizing the output capacitance that has to absorb the same transient.

    K-factor 161 means the flux swing is about 757 Gauss per amp of ripple. Core loss scales with the flux amplitude and the frequency, so this is the number to carry into the loss calculation rather than the inductance alone.

    What This Family Is For

    The HCMA family is the automotive high-current molded range, rated to +125 °C. It shares body sizes with the commercial HCM parts but is qualified and characterised for automotive use, with the current ratings to match the larger winding section.

    The HCMA1305 family spans 0.1 uH to 33 uH; this row sits at position 13 of 21.

    The next value up in the same family, HCMA1305-5R6-R, gives 5.60 uH at 11.5 A and DCR 12 mOhm: the extra inductance costs about 3.5 A of rated current.

    • Core material: iron powder core, 13.8 x 12.5 mm body at 5.0 mm.
    • Typical applications: body electronics; central body control module; vehicle access control system; headlamps, tail lamps and interior lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control.
    • Automotive derating practice: size against the saturation current at the hot corner and keep margin for the load transient, not just the steady-state current.

    Sizing and Layout Notes

    Copper resistance rises with temperature, so at the +125 °C limit the maximum DCR of 12.7 mOhm becomes roughly 17.9 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the AEC-Q200 grade covers the construction, not the thermal design of your board. The loss calculation is still the engineer’s job.

    • Size the saturation margin at the maximum ambient the module will see.
    • Compare against the commercial HCM row of the same size before substituting.
    • Confirm the terminal spacing against the rail voltage.

    Frequently Asked Questions

    Is this part suitable for a 48 V rail?
    The electrical ratings suit it, but isolation and creepage are board-level decisions. Check terminal spacing and any coating against the rail voltage.

    How does this differ from the commercial HCM part?
    Same molded construction and similar body sizes, but automotive qualified, characterised to +125 °C, and wound for higher current in the larger sizes. The electrical rows are not interchangeable.

    Is this part suitable for a 48 V rail?
    The electrical ratings suit it, but isolation and creepage are board-level decisions. Check terminal spacing and any coating against the rail voltage.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products