Eaton HCMA1305-6R8-R 6.80 uH AEC-Q200 Inductor, 11 A
Eaton HCMA1305-6R8-R 6.80 uH AEC-Q200 Inductor, 11 A

Eaton HCMA1305-6R8-R 6.80 uH AEC-Q200 Inductor, 11 A

Share
Eaton HCMA1305-6R8-R: AEC-Q200 high-current inductor, 6.80 uH ±20%, 11 A Irms, Isat 21 A, DCR 13 mOhm, 13.8 x 12.5 mm.
    • Product Details
    • Download

    Eaton HCMA1305-6R8-R 6.80 uH AEC-Q200 Inductor, 11 A

    HCMA1305-6R8-R at a glance: AEC-Q200 high-current inductor, 6.80 uH ±20%, 11 A Irms, Isat 21 A (20% rolloff @ +25 °C), DCR 13 mOhm, 13.8 x 12.5 mm.

    Specification Table

    ParameterValue
    Orderable part numberHCMA1305-6R8-R
    OCL (open circuit inductance)6.80 uH ±20%
    FLL minimum, at Isat4.35 uH
    Irms (DC, 40 °C rise)11 A
    Isat (20% rolloff @ +25 °C)21 A
    DCR typical @ +20 °C13 mOhm
    DCR maximum @ +20 °C15 mOhm
    K-factor (Bp-p = K x L x dI)129, Bp-p in Gauss
    Package13.8 x 12.5 mm
    Height5.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +125 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10277

    Mechanical Dimensions & Pad Layout

    HCMA1305-6R8-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10277: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    What the Numbers Mean

    This is the high-current member of the automotive molded family. Where the standard automotive parts top out at a few tens of amps, this one is built for the main DC-DC stage: thicker winding, larger body, and a saturation current that scales with it.

    At the rated 11 A the winding dissipates about 1.57 W in copper alone, using the typical DCR of 13 mOhm. That figure is the floor of the loss budget: it assumes the current is pure DC, and any ripple adds to it.

    The saturation rating reads 20% rolloff @ +25 °C. Treat it as the edge of the linear region: below it the inductance is within tolerance, above it the value droops. For a current-mode converter that means the peak current at the worst-case load step is what must fit under this number.

    Stored energy at Isat is about 1,499 uJ, which is the energy the inductor hands to the load during a transient before the control loop reacts.

    K-factor 129 means the flux swing is about 877 Gauss per amp of ripple. Core loss scales with the flux amplitude and the frequency, so this is the number to carry into the loss calculation rather than the inductance alone.

    What This Family Is For

    The HCMA family is the automotive high-current molded range, rated to +125 °C. It shares body sizes with the commercial HCM parts but is qualified and characterised for automotive use, with the current ratings to match the larger winding section.

    In the HCMA1305 line-up this part is number 15 of 21 by inductance, between 0.1 uH and 33 uH.

    One step down the table, HCMA1305-5R6-R, sits at 5.60 uH with 11.5 A and 12 mOhm – the lower inductance buys about 1.5 A of extra current in the same body.

    • Core material: iron powder core, 13.8 x 12.5 mm body at 5.0 mm.
    • Typical applications: body electronics; central body control module; vehicle access control system; headlamps, tail lamps and interior lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control.
    • Automotive derating practice: size against the saturation current at the hot corner and keep margin for the load transient, not just the steady-state current.

    Design Notes

    Copper resistance rises with temperature, so at the +125 °C limit the maximum DCR of 15 mOhm becomes roughly 21.2 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the AEC-Q200 grade covers the construction, not the thermal design of your board. The loss calculation is still the engineer’s job.

    • Size the saturation margin at the maximum ambient the module will see.
    • Check the current derating at the maximum ambient of the module.
    • Verify the shielding against the EMC plan for the board.

    Frequently Asked Questions

    What current can it carry continuously?
    The Irms column, which is the DC current for the stated temperature rise without core loss. Continuous operation also depends on board copper and airflow, so the data sheet derating curves apply.

    Is this part suitable for a 48 V rail?
    The electrical ratings suit it, but isolation and creepage are board-level decisions. Check terminal spacing and any coating against the rail voltage.

    Is this part suitable for a 48 V rail?
    The electrical ratings suit it, but isolation and creepage are board-level decisions. Check terminal spacing and any coating against the rail voltage.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products