Eaton HCMA1305-R10-R AEC-Q200 Inductor 0.10 uH, Isat 118 A
Eaton HCMA1305-R10-R AEC-Q200 Inductor 0.10 uH, Isat 118 A

Eaton HCMA1305-R10-R AEC-Q200 Inductor 0.10 uH, Isat 118 A

Share
Eaton HCMA1305-R10-R: AEC-Q200 high-current inductor, 0.10 uH ±20%, 55 A Irms, Isat 118 A, DCR 0.52 mOhm, 13.8 x 12.5 mm.
    • Product Details
    • Download

    Eaton HCMA1305-R10-R AEC-Q200 Inductor 0.10 uH, Isat 118 A

    HCMA1305-R10-R at a glance: AEC-Q200 high-current inductor, 0.10 uH ±20%, 55 A Irms, Isat 118 A (20% rolloff @ +25 °C), DCR 0.52 mOhm, 13.8 x 12.5 mm.

    Key Specifications

    ParameterValue
    Orderable part numberHCMA1305-R10-R
    OCL (open circuit inductance)0.10 uH ±20%
    FLL minimum, at Isat0.064 uH
    Irms (DC, 40 °C rise)55 A
    Isat (20% rolloff @ +25 °C)118 A
    DCR typical @ +20 °C0.52 mOhm
    DCR maximum @ +20 °C0.59 mOhm
    K-factor (Bp-p = K x L x dI)848, Bp-p in Gauss
    Package13.8 x 12.5 mm
    Height5.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +125 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10277

    Mechanical Drawing

    HCMA1305-R10-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10277: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    Reading the Data Sheet

    Molded powder core, shielded, AEC-Q200, +125 °C: the part is aimed at automotive DC-DC converters and motor-drive front ends where the inductor carries the full load current and the board has to pass EMC without a shield can.

    At the rated 55 A the winding dissipates about 1.57 W in copper alone, using the typical DCR of 0.52 mOhm. That figure is the floor of the loss budget: it assumes the current is pure DC, and any ripple adds to it.

    Saturation is quoted as 20% rolloff @ +25 °C. At that point the inductance has fallen to the stated fraction of its nominal value – the part is not damaged there, it simply stops behaving like the inductance on the label. Design the peak current to stay inside that boundary with margin for tolerance.

    The core stores roughly 696 uJ at the saturation point – a useful figure when sizing the output capacitance that has to absorb the same transient.

    With K = 848, a peak-to-peak ripple of one amp produces roughly 84.8 Gauss of flux swing. Read the core-loss graph at that amplitude and at the switching frequency to get the core contribution to the total loss.

    Where This Series Fits

    The HCMA family is the automotive high-current molded range, rated to +125 °C. It shares body sizes with the commercial HCM parts but is qualified and characterised for automotive use, with the current ratings to match the larger winding section.

    Of the 21 values listed for HCMA1305, this is the 1th, in a family covering 0.1 uH to 33 uH.

    The next value up in the same family, HCMA1305-R22-R, gives 0.22 uH at 51 A and DCR 0.63 mOhm: the extra inductance costs about 0 A of rated current.

    • Core material: iron powder core, 13.8 x 12.5 mm body at 5.0 mm.
    • Typical applications: body electronics; central body control module; vehicle access control system; headlamps, tail lamps and interior lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control.
    • Automotive derating practice: size against the saturation current at the hot corner and keep margin for the load transient, not just the steady-state current.

    Putting It to Work

    Copper resistance rises with temperature, so at the +125 °C limit the maximum DCR of 0.59 mOhm becomes roughly 0.833 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the AEC-Q200 grade covers the construction, not the thermal design of your board. The loss calculation is still the engineer’s job.

    • Confirm the terminal spacing against the rail voltage.
    • Check the current derating at the maximum ambient of the module.
    • Size the saturation margin at the maximum ambient the module will see.

    Frequently Asked Questions

    Is it shielded?
    Yes – the winding is enclosed in the molded powder core, which keeps the external field low enough for dense automotive boards.

    Is this part suitable for a 48 V rail?
    The electrical ratings suit it, but isolation and creepage are board-level decisions. Check terminal spacing and any coating against the rail voltage.

    Is it shielded?
    Yes – the winding is enclosed in the molded powder core, which keeps the external field low enough for dense automotive boards.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products