Eaton HCMA1305-R33-R 0.33 uH AEC-Q200 Inductor, 42 A
Eaton HCMA1305-R33-R 0.33 uH AEC-Q200 Inductor, 42 A

Eaton HCMA1305-R33-R 0.33 uH AEC-Q200 Inductor, 42 A

Share
Eaton HCMA1305-R33-R: AEC-Q200 high-current inductor, 0.33 uH ±20%, 42 A Irms, Isat 80 A, DCR 0.8 mOhm, 13.8 x 12.5 mm.
    • Product Details
    • Download

    Eaton HCMA1305-R33-R 0.33 uH AEC-Q200 Inductor, 42 A

    HCMA1305-R33-R at a glance: AEC-Q200 high-current inductor, 0.33 uH ±20%, 42 A Irms, Isat 80 A (20% rolloff @ +25 °C), DCR 0.8 mOhm, 13.8 x 12.5 mm.

    Specification Table

    ParameterValue
    Orderable part numberHCMA1305-R33-R
    OCL (open circuit inductance)0.33 uH ±20%
    FLL minimum, at Isat0.21 uH
    Irms (DC, 40 °C rise)42 A
    Isat (20% rolloff @ +25 °C)80 A
    DCR typical @ +20 °C0.8 mOhm
    DCR maximum @ +20 °C0.92 mOhm
    K-factor (Bp-p = K x L x dI)506, Bp-p in Gauss
    Package13.8 x 12.5 mm
    Height5.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +125 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10277

    Mechanical Drawing

    HCMA1305-R33-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10277: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    What the Numbers Mean

    This is the high-current member of the automotive molded family. Where the standard automotive parts top out at a few tens of amps, this one is built for the main DC-DC stage: thicker winding, larger body, and a saturation current that scales with it.

    At the rated 42 A the winding dissipates about 1.41 W in copper alone, using the typical DCR of 0.8 mOhm. That figure is the floor of the loss budget: it assumes the current is pure DC, and any ripple adds to it.

    Saturation is quoted as 20% rolloff @ +25 °C. At that point the inductance has fallen to the stated fraction of its nominal value – the part is not damaged there, it simply stops behaving like the inductance on the label. Design the peak current to stay inside that boundary with margin for tolerance.

    The core stores roughly 1,056 uJ at the saturation point – a useful figure when sizing the output capacitance that has to absorb the same transient.

    K-factor 506 means the flux swing is about 167 Gauss per amp of ripple. Core loss scales with the flux amplitude and the frequency, so this is the number to carry into the loss calculation rather than the inductance alone.

    Where This Series Fits

    The HCMA family is the automotive high-current molded range, rated to +125 °C. It shares body sizes with the commercial HCM parts but is qualified and characterised for automotive use, with the current ratings to match the larger winding section.

    Within the HCMA1305 family this is value 3 of 21, in a range that runs from 0.1 uH to 33 uH.

    One step down the table, HCMA1305-R22-R, sits at 0.22 uH with 51 A and 0.63 mOhm – the lower inductance buys about 13 A of extra current in the same body.

    • Core material: iron powder core, 13.8 x 12.5 mm body at 5.0 mm.
    • Typical applications: body electronics; central body control module; vehicle access control system; headlamps, tail lamps and interior lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control.
    • Automotive derating practice: size against the saturation current at the hot corner and keep margin for the load transient, not just the steady-state current.

    Putting It to Work

    Copper resistance rises with temperature, so at the +125 °C limit the maximum DCR of 0.92 mOhm becomes roughly 1.3 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the AEC-Q200 grade covers the construction, not the thermal design of your board. The loss calculation is still the engineer’s job.

    • Confirm the terminal spacing against the rail voltage.
    • Check the terminal spacing against the rail voltage and the coating scheme.
    • Verify the shielding against the EMC plan for the board.

    Frequently Asked Questions

    Can it be used on a 48 V rail?
    The inductance and current ratings suit 48 V converters, but the insulation system and creepage are board-level concerns. Check the terminal spacing and conformal coating against the rail voltage.

    How does this differ from the commercial HCM part?
    Same molded construction and similar body sizes, but automotive qualified, characterised to +125 °C, and wound for higher current in the larger sizes. The electrical rows are not interchangeable.

    Is this part suitable for a 48 V rail?
    The electrical ratings suit it, but isolation and creepage are board-level decisions. Check terminal spacing and any coating against the rail voltage.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products