Eaton HCMA1707-6R8-R AEC-Q200 Inductor 6.8 uH, Isat 22 A
Eaton HCMA1707-6R8-R AEC-Q200 Inductor 6.8 uH, Isat 22 A

Eaton HCMA1707-6R8-R AEC-Q200 Inductor 6.8 uH, Isat 22 A

Share
Eaton HCMA1707-6R8-R: AEC-Q200 high-current inductor, 6.8 uH ±20%, 20 A Irms, Isat 22 A, DCR 6.55 mOhm, 17.5 x 17.2 mm.
    • Product Details
    • Download

    Eaton HCMA1707-6R8-R AEC-Q200 Inductor 6.8 uH, Isat 22 A

    HCMA1707-6R8-R at a glance: AEC-Q200 high-current inductor, 6.8 uH ±20%, 20 A Irms, Isat 22 A (20% rolloff @ +25 °C), DCR 6.55 mOhm, 17.5 x 17.2 mm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberHCMA1707-6R8-R
    OCL (open circuit inductance)6.8 uH ±20%
    FLL minimum, at Isat4.35 uH
    Irms (DC, 40 °C rise)20 A
    Isat (20% rolloff @ +25 °C)22 A
    DCR typical @ +20 °C6.55 mOhm
    DCR maximum @ +20 °C7.55 mOhm
    K-factor (Bp-p = K x L x dI)60, Bp-p in Gauss
    Package17.5 x 17.2 mm
    Height7.0 mm
    MountingSurface mount
    Operating temperature-55 °C to +125 °C (ambient plus self-heating)
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10296

    Mechanical Drawing

    HCMA1707-6R8-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10296: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    Reading the Data Sheet

    Molded powder core, shielded, AEC-Q200, +125 °C: the part is aimed at automotive DC-DC converters and motor-drive front ends where the inductor carries the full load current and the board has to pass EMC without a shield can.

    At the rated 20 A the winding dissipates about 2.62 W in copper alone, using the typical DCR of 6.55 mOhm. That figure is the floor of the loss budget: it assumes the current is pure DC, and any ripple adds to it.

    Isat is specified as 20% rolloff @ +25 °C, so the number is a rolloff criterion rather than an absolute maximum. The useful working range extends a little beyond it on a soft saturation core, but the loop compensation has to be designed for the inductance that remains.

    Stored energy at Isat is about 1,646 uJ, which is the energy the inductor hands to the load during a transient before the control loop reacts.

    The K-factor of 60 converts inductance and ripple into flux swing: each amp of peak-to-peak ripple moves the core through about 408 Gauss of Bp-p, the figure the core-loss curve is plotted against.

    Where This Series Fits

    The HCMA family is the automotive high-current molded range, rated to +125 °C. It shares body sizes with the commercial HCM parts but is qualified and characterised for automotive use, with the current ratings to match the larger winding section.

    In the HCMA1707 line-up this part is number 4 of 11 by inductance, between 1.5 uH and 68 uH.

    One step down the table, HCMA1707-4R7-R, sits at 4.7 uH with 27 A and 4.12 mOhm – the lower inductance buys about 11 A of extra current in the same body.

    • Core material: iron powder core, 17.5 x 17.2 mm body at 7.0 mm.
    • Typical applications: body electronics; central body control module; headlamps, tai lamps and interior lighting; heating ventilation and air conditioning controllers (hvac); doors, window lift and seat control; advanced driver assistance systems.
    • Automotive derating practice: size against the saturation current at the hot corner and keep margin for the load transient, not just the steady-state current.

    Design Notes

    Copper resistance rises with temperature, so at the +125 °C limit the maximum DCR of 7.55 mOhm becomes roughly 10.7 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: the AEC-Q200 grade covers the construction, not the thermal design of your board. The loss calculation is still the engineer’s job.

    • Verify the shielding against the EMC plan for the board.
    • Verify the shielding against the EMC plan for the board.
    • Confirm the terminal spacing against the rail voltage.

    Frequently Asked Questions

    Can it be used on a 48 V rail?
    The inductance and current ratings suit 48 V converters, but the insulation system and creepage are board-level concerns. Check the terminal spacing and conformal coating against the rail voltage.

    Is this part suitable for a 48 V rail?
    The electrical ratings suit it, but isolation and creepage are board-level decisions. Check terminal spacing and any coating against the rail voltage.

    How does this differ from the commercial HCM part?
    Same molded construction and similar body sizes, but automotive qualified, characterised to +125 °C, and wound for higher current in the larger sizes. The electrical rows are not interchangeable.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products