Eaton HCP0704-2R3-R 2.30 uH High-Current Inductor 16.5 mOhm
Eaton HCP0704-2R3-R 2.30 uH High-Current Inductor 16.5 mOhm

Eaton HCP0704-2R3-R 2.30 uH High-Current Inductor 16.5 mOhm

Share
Eaton HCP0704-2R3-R: iron powder high-current inductor, 2.30 uH ±25%, 7.5 A Irms, Isat 11.5 A, DCR 16.5 mOhm, 6.8 x 6.8 mm.
    • Product Details
    • Download

    Eaton HCP0704-2R3-R 2.30 uH High-Current Inductor 16.5 mOhm

    HCP0704-2R3-R at a glance: iron powder high-current inductor, 2.30 uH ±25%, 7.5 A Irms, Isat 11.5 A (20% rolloff @ +25 °C), DCR 16.5 mOhm, 6.8 x 6.8 mm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberHCP0704-2R3-R
    OCL (open circuit inductance)2.30 uH ±25%
    FLL minimum, at Isat1.56 uH
    Irms (DC, 40 °C rise)7.5 A
    Isat (20% rolloff @ +25 °C)11.5 A
    DCR typical @ +20 °C16.5 mOhm
    K-factor (Bp-p = K x L x dI)164, Bp-p in Gauss
    Package6.8 x 6.8 mm
    Height4.2 mm
    MountingSurface mount
    Operating temperature-40 °C to +155 °C (ambient plus self-heating)
    QualificationCommercial grade
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 4348

    Mechanical Dimensions & Pad Layout

    HCP0704-2R3-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 4348: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    The Figures Explained

    A shielded iron powder inductor for high-current switching stages. The distributed gap of the powder core spreads the stored energy through the volume, so the part handles a large DC component without local saturation, and the shielding keeps the fringing field small.

    Copper loss at the rated current works out to roughly 0.928 W from a typical DCR of 16.5 mOhm at 7.5 A. It is the number to start a thermal stack-up with, before core loss and before AC resistance rise.

    Isat is specified as 20% rolloff @ +25 °C, so the number is a rolloff criterion rather than an absolute maximum. The useful working range extends a little beyond it on a soft saturation core, but the loop compensation has to be designed for the inductance that remains.

    Stored energy at Isat is about 152 uJ, which is the energy the inductor hands to the load during a transient before the control loop reacts.

    The K-factor of 164 converts inductance and ripple into flux swing: each amp of peak-to-peak ripple moves the core through about 378 Gauss of Bp-p, the figure the core-loss curve is plotted against.

    Where This Series Fits

    The HCP family is the iron powder, shielded, high-current range for VRM and point-of-load work. It covers modest inductance values at high DC bias, with the soft saturation curve that iron powder is chosen for.

    Of the 7 values listed for HCP0704, this is the 5th, in a family covering 0.4 uH to 4.7 uH.

    One step down the table, HCP0704-1R8-R, sits at 1.80 uH with 8.5 A and 11 mOhm – the lower inductance buys about 2.5 A of extra current in the same body.

    • Core material: iron powder core, 6.8 x 6.8 mm body at 4.2 mm.
    • Typical applications: voltage regulator module (vrm); multi-phase regulators; desktop and servers; base station equipment; notebook and laptop regulators; data networking and storage systems.
    • Iron powder has a soft saturation curve but a lower permeability than ferrite, so the turns count – and therefore the DCR – is higher for the same inductance.

    Design Notes

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 16.5 mOhm becomes roughly 25.3 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: at high DC bias the inductance is well below OCL. Use the inductance-versus-current curve for the ripple calculation, not the headline value.

    • Verify the footprint against the recommended pad layout.
    • Read the inductance at the actual DC bias from the curve before sizing ripple.
    • Confirm the K-factor against the ripple amplitude for the core-loss estimate.

    Frequently Asked Questions

    Is the part suitable for a high-frequency design?
    Iron powder suits the low-to-mid hundreds of kilohertz range. Above that the loss of the powder material rises faster than ferrite, so compare the loss curves before choosing.

    What core loss should I expect?
    Read the core-loss curve at the flux amplitude implied by the K-factor and the ripple, at the switching frequency. Core loss is quoted per unit volume, so compare curves rather than single numbers.

    Why iron powder rather than ferrite?
    Iron powder saturates at a much higher flux density, so a small core can carry a large DC bias. The price is lower permeability, which means more turns and higher DCR for the same inductance.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products