Eaton HCP0704-R60-R 0.60 uH Iron Powder Inductor, 14 A
Eaton HCP0704-R60-R 0.60 uH Iron Powder Inductor, 14 A

Eaton HCP0704-R60-R 0.60 uH Iron Powder Inductor, 14 A

Share
Eaton HCP0704-R60-R: iron powder high-current inductor, 0.60 uH ±25%, 14 A Irms, Isat 21 A, DCR 4.5 mOhm, 6.8 x 6.8 mm.
    • Product Details
    • Download

    Eaton HCP0704-R60-R 0.60 uH Iron Powder Inductor, 14 A

    HCP0704-R60-R at a glance: iron powder high-current inductor, 0.60 uH ±25%, 14 A Irms, Isat 21 A (20% rolloff @ +25 °C), DCR 4.5 mOhm, 6.8 x 6.8 mm.

    Key Specifications

    ParameterValue
    Orderable part numberHCP0704-R60-R
    OCL (open circuit inductance)0.60 uH ±25%
    FLL minimum, at Isat0.42 uH
    Irms (DC, 40 °C rise)14 A
    Isat (20% rolloff @ +25 °C)21 A
    DCR typical @ +20 °C4.5 mOhm
    K-factor (Bp-p = K x L x dI)314, Bp-p in Gauss
    Package6.8 x 6.8 mm
    Height4.2 mm
    MountingSurface mount
    Operating temperature-40 °C to +155 °C (ambient plus self-heating)
    QualificationCommercial grade
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 4348

    Outline Drawing

    HCP0704-R60-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 4348: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    What the Numbers Mean

    The core here is iron powder, pressed into a shielded body. Iron powder has lower permeability than ferrite but far higher saturation flux density, which is why this family is used where the DC bias is large and the inductance value is modest.

    At the rated 14 A the winding dissipates about 0.882 W in copper alone, using the typical DCR of 4.5 mOhm. That figure is the floor of the loss budget: it assumes the current is pure DC, and any ripple adds to it.

    The saturation rating reads 20% rolloff @ +25 °C. Treat it as the edge of the linear region: below it the inductance is within tolerance, above it the value droops. For a current-mode converter that means the peak current at the worst-case load step is what must fit under this number.

    At Isat the part holds about 132 uJ. On a multiphase rail that is the energy per phase available to bridge a load step, which sets how much bulk capacitance the controller still needs.

    The K-factor of 314 converts inductance and ripple into flux swing: each amp of peak-to-peak ripple moves the core through about 188 Gauss of Bp-p, the figure the core-loss curve is plotted against.

    What This Family Is For

    The HCP family is the iron powder, shielded, high-current range for VRM and point-of-load work. It covers modest inductance values at high DC bias, with the soft saturation curve that iron powder is chosen for.

    Within the HCP0704 family this is value 2 of 7, in a range that runs from 0.4 uH to 4.7 uH.

    The next value up in the same family, HCP0704-1R0-R, gives 1.00 uH at 12 A and DCR 6.2 mOhm: the extra inductance costs about 5 A of rated current.

    • Core material: iron powder core, 6.8 x 6.8 mm body at 4.2 mm.
    • Typical applications: voltage regulator module (vrm); multi-phase regulators; desktop and servers; base station equipment; notebook and laptop regulators; data networking and storage systems.
    • Iron powder has a soft saturation curve but a lower permeability than ferrite, so the turns count – and therefore the DCR – is higher for the same inductance.

    Design Notes

    Copper resistance rises with temperature, so at the +155 °C limit the maximum DCR of 4.5 mOhm becomes roughly 6.89 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: at high DC bias the inductance is well below OCL. Use the inductance-versus-current curve for the ripple calculation, not the headline value.

    • Read the inductance at the actual DC bias from the curve before sizing ripple.
    • Check the K-factor against the ripple amplitude to estimate core loss.
    • Read the inductance at the actual DC bias from the curve before sizing ripple.

    Frequently Asked Questions

    Why iron powder rather than ferrite?
    Iron powder saturates at a much higher flux density, so a small core can carry a large DC bias. The price is lower permeability, which means more turns and higher DCR for the same inductance.

    What core loss should I expect?
    Read the core-loss curve at the flux amplitude implied by the K-factor and the ripple, at the switching frequency. Core loss is quoted per unit volume, so compare curves rather than single numbers.

    What does the K-factor tell me?
    It converts inductance and ripple current into flux swing: K times L times delta-I gives Bp-p. That amplitude is what the core-loss graph is plotted against.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products