Eaton HCP0805-R40-R Iron Powder Inductor 0.40 uH, Isat 32 A
Eaton HCP0805-R40-R Iron Powder Inductor 0.40 uH, Isat 32 A

Eaton HCP0805-R40-R Iron Powder Inductor 0.40 uH, Isat 32 A

Share
Eaton HCP0805-R40-R: iron powder high-current inductor, 0.40 uH ±20%, 20 A Irms, Isat 32 A, DCR 3.1 mOhm, 7.9 x 7.6 mm.
    • Product Details
    • Download

    Eaton HCP0805-R40-R Iron Powder Inductor 0.40 uH, Isat 32 A

    HCP0805-R40-R at a glance: iron powder high-current inductor, 0.40 uH ±20%, 20 A Irms, Isat 32 A (20% rolloff @ +25 °C), DCR 3.1 mOhm, 7.9 x 7.6 mm.

    Key Specifications

    ParameterValue
    Orderable part numberHCP0805-R40-R
    OCL (open circuit inductance)0.40 uH ±20%
    FLL minimum, at Isat0.26 uH
    Irms (DC, 40 °C rise)20 A
    Isat (20% rolloff @ +25 °C)32 A
    DCR typical @ +20 °C3.1 mOhm
    K-factor (Bp-p = K x L x dI)376, Bp-p in Gauss
    Package7.9 x 7.6 mm
    Height5.0 mm
    MountingSurface mount
    Operating temperature-40 °C to +125 °C (ambient plus self-heating)
    QualificationCommercial grade
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 4349

    Mechanical Dimensions & Pad Layout

    HCP0805-R40-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 4349: outline with
    rated mm dimensions, recommended pad layout and winding schematic. Tolerances are stated on
    the drawing itself.

    What the Numbers Mean

    Iron powder core in a shielded surface-mount body: the material gives a soft saturation curve, so inductance falls gradually with current rather than dropping off a cliff. The part is aimed at VRM and point-of-load stages where the inductor spends its working life part-way up the saturation curve.

    At the rated 20 A the winding dissipates about 1.24 W in copper alone, using the typical DCR of 3.1 mOhm. That figure is the floor of the loss budget: it assumes the current is pure DC, and any ripple adds to it.

    The Isat column is 20% rolloff @ +25 °C. Note what it does and does not mean: it is a defined rolloff point, not a destruction limit. Above it the inductance continues to fall, which is why the transient peak current should be checked against the curve, not just against the number.

    The core stores roughly 205 uJ at the saturation point – a useful figure when sizing the output capacitance that has to absorb the same transient.

    With K = 376, a peak-to-peak ripple of one amp produces roughly 150 Gauss of flux swing. Read the core-loss graph at that amplitude and at the switching frequency to get the core contribution to the total loss.

    What This Family Is For

    The HCP family is the iron powder, shielded, high-current range for VRM and point-of-load work. It covers modest inductance values at high DC bias, with the soft saturation curve that iron powder is chosen for.

    Of the 5 values listed for HCP0805, this is the 1th, in a family covering 0.4 uH to 2.2 uH.

    One step down the table, HCP0805-R68-R, sits at 0.68 uH with 17.5 A and 4.5 mOhm – the lower inductance buys about 0 A of extra current in the same body.

    • Core material: iron powder core, 7.9 x 7.6 mm body at 5.0 mm.
    • Typical applications: multi-phase regulators; voltage regulator modules (vrms); distributed power systems dc-dc converters; desktop and server vrms and evrds; point-of-load (pol) modules; field programmable gate array (fpga) dc-dc converters.
    • Iron powder has a soft saturation curve but a lower permeability than ferrite, so the turns count – and therefore the DCR – is higher for the same inductance.

    Putting It to Work

    Copper resistance rises with temperature, so at the +125 °C limit the maximum DCR of 3.1 mOhm becomes roughly 4.38 mOhm. That is the figure to put into a hot-enclosure loss calculation; the +20 °C column is a bench number.

    Design note: at high DC bias the inductance is well below OCL. Use the inductance-versus-current curve for the ripple calculation, not the headline value.

    • Check the K-factor against the ripple amplitude to estimate core loss.
    • Check the inductance at the operating bias, not the catalogue value.
    • Read the inductance at the actual DC bias from the curve before sizing ripple.

    Frequently Asked Questions

    Why iron powder rather than ferrite?
    Iron powder saturates at a much higher flux density, so a small core can carry a large DC bias. The price is lower permeability, which means more turns and higher DCR for the same inductance.

    Why iron powder rather than ferrite?
    Iron powder saturates at a much higher flux density, so a small core can carry a large DC bias. The price is lower permeability, which means more turns and higher DCR for the same inductance.

    Is the saturation curve linear?
    No – it is deliberately soft. Inductance droops progressively above the rated current, which is why the ripple calculation should use the inductance at the actual bias, not the headline value.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products