Eaton HPAL1V1040-1R5-R 1.5 uH Inductor, Isat 24 A
Eaton HPAL1V1040-1R5-R 1.5 uH Inductor, Isat 24 A

Eaton HPAL1V1040-1R5-R 1.5 uH Inductor, Isat 24 A

Share
HPAL1V1040-1R5-R: high-current power inductor, 1.5 uH, 16 A, Isat 24 A, DCR 4 mOhm.
    • Product Details
    • Download

    Eaton HPAL1V1040-1R5-R 1.5 uH Inductor, Isat 24 A

    HPAL1V1040-1R5-R at a glance: high-current power inductor, 1.5 uH, 16 A, Isat 24 A, DCR 4 mOhm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberHPAL1V1040-1R5-R
    Inductance1.5 uH ±20%
    DCR maximum @ +25 °C4 mOhm
    Irms (DC, 40 °C rise)16 A
    Isat24 A
    FLL minimum (at Isat)0.84 uH
    SRF typical38 MHz
    K-factor296
    MountingSurface mount
    Operating temperature-55 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 11083

    Mechanical Dimensions & Pad Layout

    Outline drawing and pad layout are on page 2 of Eaton Technical Data 11083; the package column above gives the body size in millimetres.

    How to Read These Ratings

    The part is built around a distributed-gap core: the energy is stored through the volume of the magnetic material rather than in a single discrete gap, which is what produces the gradual rolloff and the low fringing field. Copper loss and core loss are traded against each other in the winding and body proportions.

    At 16 A the winding dissipates about 1.02 W in copper, using the 4 mOhm figure. That is the DC floor of the loss budget: ripple and core loss come on top of it.

    Saturation is reached at 24 A. Beyond that point the inductance falls on the soft part of the curve, and the converter’s ripple grows faster than the load current does.

    Within the HPAL1V1040 family this is value 9 of 19, in a range that runs from 0.22 to 47 uH.

    Series Positioning

    The power inductor family covers sub-microhenry to tens of microhenry at currents from a few amps to tens of amps, in shielded surface-mount bodies. The data sheet rows carry both typical and maximum DCR so the loss budget can be built either way.

    • DCR is quoted at +20 °C. Copper resistance rises about 0.4 % per °C, so the hot loss is higher than the cold figure.
    • Typical applications: voltage regulator module (vrm); multi-phase regulators; point-of-load modules (pol); desktop and server vrms and evrds; base station equipment.
    • Design note: ripple from OCL, thermal from Irms, transient from Isat. Three different numbers, three different checks.

    Frequently Asked Questions

    How much inductance is left at rated current?
    The FLL column gives the inductance at saturation current. Ripple at full load should be calculated with FLL, not with the zero-bias value.

    Why are there two DCR columns?
    Typical and maximum. A guaranteed thermal design uses the maximum; a nominal efficiency calculation can use the typical.

    What is the difference between Irms and Isat?
    Irms is the DC current that produces the rated temperature rise. Isat is the peak current at which inductance has fallen by a defined percentage. A converter can run above Irms briefly but must stay inside Isat.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products