Eaton MCL1005-2R4-R 2.4 nH Chip Inductor, 8 Q
Eaton MCL1005-2R4-R 2.4 nH Chip Inductor, 8 Q

Eaton MCL1005-2R4-R 2.4 nH Chip Inductor, 8 Q

Share
MCL1005-2R4-R: multilayer chip inductor, 2.4 nH ±0.3nH, Q 8, SRF 6000 MHz, 300 mA, DCR 150 mOhm.
    • Product Details
    • Download

    Eaton MCL1005-2R4-R 2.4 nH Chip Inductor, 8 Q

    MCL1005-2R4-R at a glance: multilayer chip inductor, 2.4 nH ±0.3nH, Q 8, SRF 6000 MHz, 300 mA, DCR 150 mOhm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberMCL1005-2R4-R
    Inductance2.4 nH ±0.3nH
    Q minimum8
    DCR maximum @ +25 °C150 mOhm
    Rated current maximum300 mA
    SRF minimum6000 MHz
    Test frequency100 MHz
    Test voltage50 mV
    Package1.0 x 0.5 mm
    Size code1005 (0402)
    MountingSurface mount
    Operating temperature-55 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10925

    Dimensions and Pad Layout

    MCL1005-2R4-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10925: outline with rated mm dimensions, pad layout and marking. Tolerances are stated on the drawing.

    Reading the Data Sheet

    Where a circuit needs a small, stable inductance in a package measured in millimetres, the multilayer chip is the default. Its self-resonant frequency is the practical ceiling – above it the part behaves like a capacitor, so the SRF column is the first thing to check against the operating band.

    The row reads 2.4 nH ±0.3nH with a minimum Q of 8 at 100 MHz. Q is the ratio of reactance to resistance at that frequency, so a Q of 8 means the part’s loss is about 12.5 % of its reactance in that band.

    Self-resonance is quoted as 6000 MHz minimum. Below it the part is inductive; above it the inter-layer capacitance takes over. The margin between the operating band and 6000 MHz is the design headroom.

    Within the MCL1005 family this is value 10 of 46, in a range that runs from 0.001 to 0.36 nH.

    What This Family Is For

    The multilayer chip family covers nanohenry to a few microhenry values in 0402 through 1812 bodies. It is the range where the inductance is too small for a wound part to be practical and where the self-resonant frequency sets the usable band.

    • The rated current is a thermal limit for the part in free air, not a saturation limit. At high ambient the current has to be derated.
    • Typical applications: industrial connectivity (iot); wireless communiations; bluetooth; wifi; antenna.
    • Design note: compare SRF against the highest frequency the circuit will see, not just the fundamental.

    Frequently Asked Questions

    How much does the value drift with temperature?
    The data sheet gives the tolerance band; the drift inside that band is small for this construction because there is no mechanical winding to move.

    Can I replace a wire-wound chip with this part?
    Only if the Q and the current rating suit the circuit. Multilayer parts have lower Q and lower current capability than wire-wound parts of the same size.

    What happens above the self-resonant frequency?
    The part becomes capacitive. Any filter or matching design has to keep the operating band below SRF, with margin for the tolerance of the value.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products