Eaton MCL1005-820-R 82.0 nH Chip Inductor, 100 Q
Eaton MCL1005-820-R 82.0 nH Chip Inductor, 100 Q

Eaton MCL1005-820-R 82.0 nH Chip Inductor, 100 Q

Share
MCL1005-820-R: multilayer chip inductor, 82.0 nH 150, Q 100, SRF 8 MHz, 2 mA, DCR 750000 mOhm.
    • Product Details
    • Download

    Eaton MCL1005-820-R 82.0 nH Chip Inductor, 100 Q

    MCL1005-820-R at a glance: multilayer chip inductor, 82.0 nH 150, Q 100, SRF 8 MHz, 2 mA, DCR 750000 mOhm.

    Specification Table

    ParameterValue
    Orderable part numberMCL1005-820-R
    Inductance82.0 nH 150
    Q minimum100
    DCR maximum @ +25 °C750000 mOhm
    Rated current maximum2 mA
    SRF minimum8 MHz
    Test frequency50 MHz
    Package1.0 x 0.5 mm
    Size code1005 (0402)
    MountingSurface mount
    Operating temperature-55 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10925

    Mechanical Drawing

    MCL1005-820-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10925: outline with rated mm dimensions, pad layout and marking. Tolerances are stated on the drawing.

    Reading the Data Sheet

    This is a surface-mount multilayer inductor: printed coil, sintered body, silver terminations. The value is quoted at a defined test frequency because at these inductances the measurement conditions matter as much as the part.

    The row reads 82.0 nH 150 with a minimum Q of 100 at 50 MHz. Q is the ratio of reactance to resistance at that frequency, so a Q of 100 means the part’s loss is about 1 % of its reactance in that band.

    Self-resonance is quoted as 8 MHz minimum. Below it the part is inductive; above it the inter-layer capacitance takes over. The margin between the operating band and 8 MHz is the design headroom.

    Within the MCL1005 family this is value 38 of 46, in a range that runs from 0.001 to 0.36 nH.

    Positioning in the Range

    The multilayer chip family covers nanohenry to a few microhenry values in 0402 through 1812 bodies. It is the range where the inductance is too small for a wound part to be practical and where the self-resonant frequency sets the usable band.

    • The rated current is a thermal limit for the part in free air, not a saturation limit. At high ambient the current has to be derated.
    • Typical applications: industrial connectivity (iot); wireless communiations; bluetooth; wifi; antenna.
    • Design note: compare SRF against the highest frequency the circuit will see, not just the fundamental.

    Frequently Asked Questions

    What happens above the self-resonant frequency?
    The part becomes capacitive. Any filter or matching design has to keep the operating band below SRF, with margin for the tolerance of the value.

    How much does the value drift with temperature?
    The data sheet gives the tolerance band; the drift inside that band is small for this construction because there is no mechanical winding to move.

    Can I replace a wire-wound chip with this part?
    Only if the Q and the current rating suit the circuit. Multilayer parts have lower Q and lower current capability than wire-wound parts of the same size.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products