Eaton MCL1608V1-R15-R 0.15 nH Multilayer Inductor
Eaton MCL1608V1-R15-R 0.15 nH Multilayer Inductor

Eaton MCL1608V1-R15-R 0.15 nH Multilayer Inductor

Share
MCL1608V1-R15-R: multilayer chip inductor, 0.15 nH , Q -, SRF 180 MHz, 150 mA, DCR 200 mOhm.
    • Product Details
    • Download

    Eaton MCL1608V1-R15-R 0.15 nH Multilayer Inductor

    MCL1608V1-R15-R at a glance: multilayer chip inductor, 0.15 nH , Q -, SRF 180 MHz, 150 mA, DCR 200 mOhm.

    Key Specifications

    ParameterValue
    Orderable part numberMCL1608V1-R15-R
    Inductance0.15 nH
    DCR maximum @ +25 °C200 mOhm
    Rated current maximum150 mA
    SRF minimum180 MHz
    Test frequency1 MHz
    Test voltage50 mV
    Package1.6 x 0.8 mm
    Size code1608 (0603)
    MountingSurface mount
    Operating temperature-40 °C to +85 °C
    QualificationCommercial grade
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10926

    Mechanical Drawing

    MCL1608V1-R15-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10926: outline with rated mm dimensions, pad layout and marking. Tolerances are stated on the drawing.

    The Figures Explained

    This is a surface-mount multilayer inductor: printed coil, sintered body, silver terminations. The value is quoted at a defined test frequency because at these inductances the measurement conditions matter as much as the part.

    The row reads 0.15 nH with a minimum Q of – at 1 MHz. Q is the ratio of reactance to resistance at that frequency, so a Q of – means the part’s loss is about 100 % of its reactance in that band.

    Self-resonance is quoted as 180 MHz minimum. Below it the part is inductive; above it the inter-layer capacitance takes over. The margin between the operating band and 180 MHz is the design headroom.

    Within the MCL1608V1 family this is value 7 of 30, in a range that runs from 0.047 to 12 nH.

    Where This Series Fits

    The multilayer chip family covers nanohenry to a few microhenry values in 0402 through 1812 bodies. It is the range where the inductance is too small for a wound part to be practical and where the self-resonant frequency sets the usable band.

    • The rated current is a thermal limit for the part in free air, not a saturation limit. At high ambient the current has to be derated.
    • Typical applications: industrial connectivity (iot); wireless communiations; bluetooth; wifi; antenna.
    • Design note: compare SRF against the highest frequency the circuit will see, not just the fundamental.

    Frequently Asked Questions

    Why is the inductance quoted at a test frequency?
    At nanohenry values the parasitic capacitance and the measurement fixture both matter. The value is only meaningful at the frequency stated, and the Q column tells you how much of the reactance is loss at that point.

    Why is the inductance quoted at a test frequency?
    At nanohenry values the parasitic capacitance and the measurement fixture both matter. The value is only meaningful at the frequency stated, and the Q column tells you how much of the reactance is loss at that point.

    Can I replace a wire-wound chip with this part?
    Only if the Q and the current rating suit the circuit. Multilayer parts have lower Q and lower current capability than wire-wound parts of the same size.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products