Eaton MCL1608V2-150-R 15.0 nH Chip Inductor 0603
Eaton MCL1608V2-150-R 15.0 nH Chip Inductor 0603

Eaton MCL1608V2-150-R 15.0 nH Chip Inductor 0603

Share
MCL1608V2-150-R: multilayer chip inductor, 15.0 nH 300, Q 100, SRF 12 MHz, 0 mA, DCR 2300000 mOhm.
    • Product Details
    • Download

    Eaton MCL1608V2-150-R 15.0 nH Chip Inductor 0603

    MCL1608V2-150-R at a glance: multilayer chip inductor, 15.0 nH 300, Q 100, SRF 12 MHz, 0 mA, DCR 2300000 mOhm.

    Specification Table

    ParameterValue
    Orderable part numberMCL1608V2-150-R
    Inductance15.0 nH 300
    Q minimum100
    DCR maximum @ +25 °C2300000 mOhm
    Rated current maximum0 mA
    SRF minimum12 MHz
    Test frequency50 MHz
    Package1.6 x 0.8 mm
    Size code1608 (0603)
    MountingSurface mount
    Operating temperature-40 °C to +85 °C
    QualificationCommercial grade
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10927

    Mechanical Drawing

    MCL1608V2-150-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10927: outline with rated mm dimensions, pad layout and marking. Tolerances are stated on the drawing.

    The Figures Explained

    This is a surface-mount multilayer inductor: printed coil, sintered body, silver terminations. The value is quoted at a defined test frequency because at these inductances the measurement conditions matter as much as the part.

    The row reads 15.0 nH 300 with a minimum Q of 100 at 50 MHz. Q is the ratio of reactance to resistance at that frequency, so a Q of 100 means the part’s loss is about 1 % of its reactance in that band.

    Self-resonance is quoted as 12 MHz minimum. Below it the part is inductive; above it the inter-layer capacitance takes over. The margin between the operating band and 12 MHz is the design headroom.

    Within the MCL1608V2 family this is value 15 of 34, in a range that runs from 0.001 to 0.47 nH.

    What This Family Is For

    The multilayer chip family covers nanohenry to a few microhenry values in 0402 through 1812 bodies. It is the range where the inductance is too small for a wound part to be practical and where the self-resonant frequency sets the usable band.

    • The rated current is a thermal limit for the part in free air, not a saturation limit. At high ambient the current has to be derated.
    • Typical applications: industrial connectivity (iot); wireless communiations; bluetooth; wifi; antenna.
    • Design note: compare SRF against the highest frequency the circuit will see, not just the fundamental.

    Frequently Asked Questions

    What happens above the self-resonant frequency?
    The part becomes capacitive. Any filter or matching design has to keep the operating band below SRF, with margin for the tolerance of the value.

    Can I replace a wire-wound chip with this part?
    Only if the Q and the current rating suit the circuit. Multilayer parts have lower Q and lower current capability than wire-wound parts of the same size.

    Can I replace a wire-wound chip with this part?
    Only if the Q and the current rating suit the circuit. Multilayer parts have lower Q and lower current capability than wire-wound parts of the same size.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products