Eaton MCL2012V2-5R6-R 5.6 nH SMD Inductor, SRF 3500 MHz
Eaton MCL2012V2-5R6-R 5.6 nH SMD Inductor, SRF 3500 MHz

Eaton MCL2012V2-5R6-R 5.6 nH SMD Inductor, SRF 3500 MHz

Share
MCL2012V2-5R6-R: multilayer chip inductor, 5.6 nH ±0.3nH, Q 15, SRF 3500 MHz, 500 mA, DCR 230 mOhm.
    • Product Details
    • Download

    Eaton MCL2012V2-5R6-R 5.6 nH SMD Inductor, SRF 3500 MHz

    MCL2012V2-5R6-R at a glance: multilayer chip inductor, 5.6 nH ±0.3nH, Q 15, SRF 3500 MHz, 500 mA, DCR 230 mOhm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberMCL2012V2-5R6-R
    Inductance5.6 nH ±0.3nH
    Q minimum15
    DCR maximum @ +25 °C230 mOhm
    Rated current maximum500 mA
    SRF minimum3500 MHz
    Test frequency100 MHz
    Test voltage50 mV
    Package2.0 x 1.25 mm
    Size code2012 (0805)
    MountingSurface mount
    Operating temperature-40 °C to +85 °C
    QualificationCommercial grade
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10929

    Mechanical Drawing

    MCL2012V2-5R6-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10929: outline with rated mm dimensions, pad layout and marking. Tolerances are stated on the drawing.

    The Figures Explained

    This is a surface-mount multilayer inductor: printed coil, sintered body, silver terminations. The value is quoted at a defined test frequency because at these inductances the measurement conditions matter as much as the part.

    The row reads 5.6 nH ±0.3nH with a minimum Q of 15 at 100 MHz. Q is the ratio of reactance to resistance at that frequency, so a Q of 15 means the part’s loss is about 6.67 % of its reactance in that band.

    Self-resonance is quoted as 3500 MHz minimum. Below it the part is inductive; above it the inter-layer capacitance takes over. The margin between the operating band and 3500 MHz is the design headroom.

    Within the MCL2012V2 family this is value 9 of 32, in a range that runs from 0.002 to 0.47 nH.

    Series Positioning

    The multilayer chip family covers nanohenry to a few microhenry values in 0402 through 1812 bodies. It is the range where the inductance is too small for a wound part to be practical and where the self-resonant frequency sets the usable band.

    • The rated current is a thermal limit for the part in free air, not a saturation limit. At high ambient the current has to be derated.
    • Typical applications: industrial connectivity (iot); wireless communiations; bluetooth; wifi; antenna.
    • Design note: compare SRF against the highest frequency the circuit will see, not just the fundamental.

    Frequently Asked Questions

    What happens above the self-resonant frequency?
    The part becomes capacitive. Any filter or matching design has to keep the operating band below SRF, with margin for the tolerance of the value.

    What happens above the self-resonant frequency?
    The part becomes capacitive. Any filter or matching design has to keep the operating band below SRF, with margin for the tolerance of the value.

    Can I replace a wire-wound chip with this part?
    Only if the Q and the current rating suit the circuit. Multilayer parts have lower Q and lower current capability than wire-wound parts of the same size.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products