Eaton MCLA1608V1-1R8-R 1.8 uH SMD Inductor, SRF 55 MHz
Eaton MCLA1608V1-1R8-R 1.8 uH SMD Inductor, SRF 55 MHz

Eaton MCLA1608V1-1R8-R 1.8 uH SMD Inductor, SRF 55 MHz

Share
MCLA1608V1-1R8-R: multilayer chip inductor, 1.8 uH ±10, Q 25, SRF 55 MHz, 25 mA, DCR 750 mOhm.
    • Product Details
    • Download

    Eaton MCLA1608V1-1R8-R 1.8 uH SMD Inductor, SRF 55 MHz

    MCLA1608V1-1R8-R at a glance: multilayer chip inductor, 1.8 uH ±10, Q 25, SRF 55 MHz, 25 mA, DCR 750 mOhm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberMCLA1608V1-1R8-R
    Inductance1.8 uH ±10
    Q minimum25
    DCR maximum @ +25 °C750 mOhm
    Rated current maximum25 mA
    SRF minimum55 MHz
    Test frequency10 MHz
    Test voltage50 mV
    Package1.6 x 0.8 mm
    Size code1608 (0603)
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10975

    Mechanical Drawing

    Outline drawing and pad layout are on page 2 of Eaton Technical Data 10975; the package column above gives the body size in millimetres.

    The Figures Explained

    This is a surface-mount multilayer inductor: printed coil, sintered body, silver terminations. The value is quoted at a defined test frequency because at these inductances the measurement conditions matter as much as the part.

    The row reads 1.8 uH ±10 with a minimum Q of 25 at 10 MHz. Q is the ratio of reactance to resistance at that frequency, so a Q of 25 means the part’s loss is about 4 % of its reactance in that band.

    Self-resonance is quoted as 55 MHz minimum. Below it the part is inductive; above it the inter-layer capacitance takes over. The margin between the operating band and 55 MHz is the design headroom.

    Within the MCLA1608V1 family this is value 20 of 24, in a range that runs from 0.047 to 3.9 nH.

    Series Positioning

    The multilayer chip family covers nanohenry to a few microhenry values in 0402 through 1812 bodies. It is the range where the inductance is too small for a wound part to be practical and where the self-resonant frequency sets the usable band.

    • The rated current is a thermal limit for the part in free air, not a saturation limit. At high ambient the current has to be derated.
    • Typical applications: adas; infotainment; wireless communications; wifi, bluetooth, satellite; antenna tuning.
    • Design note: compare SRF against the highest frequency the circuit will see, not just the fundamental.

    Frequently Asked Questions

    What happens above the self-resonant frequency?
    The part becomes capacitive. Any filter or matching design has to keep the operating band below SRF, with margin for the tolerance of the value.

    What happens above the self-resonant frequency?
    The part becomes capacitive. Any filter or matching design has to keep the operating band below SRF, with margin for the tolerance of the value.

    Can I replace a wire-wound chip with this part?
    Only if the Q and the current rating suit the circuit. Multilayer parts have lower Q and lower current capability than wire-wound parts of the same size.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products