Eaton MCLA1608V1-R390-R 0.39 nH SMD Inductor, SRF 110 MHz
Eaton MCLA1608V1-R390-R 0.39 nH SMD Inductor, SRF 110 MHz

Eaton MCLA1608V1-R390-R 0.39 nH SMD Inductor, SRF 110 MHz

Share
MCLA1608V1-R390-R: multilayer chip inductor, 0.39 nH ±10, Q 20, SRF 110 MHz, 50 mA, DCR 600 mOhm.
    • Product Details
    • Download

    Eaton MCLA1608V1-R390-R 0.39 nH SMD Inductor, SRF 110 MHz

    MCLA1608V1-R390-R at a glance: multilayer chip inductor, 0.39 nH ±10, Q 20, SRF 110 MHz, 50 mA, DCR 600 mOhm.

    Specification Table

    ParameterValue
    Orderable part numberMCLA1608V1-R390-R
    Inductance0.39 nH ±10
    Q minimum20
    DCR maximum @ +25 °C600 mOhm
    Rated current maximum50 mA
    SRF minimum110 MHz
    Test frequency25 MHz
    Test voltage50 mV
    Package1.6 x 0.8 mm
    Size code1608 (0603)
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10975

    Mechanical Drawing

    Outline drawing and pad layout are on page 2 of Eaton Technical Data 10975; the package column above gives the body size in millimetres.

    The Figures Explained

    Where a circuit needs a small, stable inductance in a package measured in millimetres, the multilayer chip is the default. Its self-resonant frequency is the practical ceiling – above it the part behaves like a capacitor, so the SRF column is the first thing to check against the operating band.

    The row reads 0.39 nH ±10 with a minimum Q of 20 at 25 MHz. Q is the ratio of reactance to resistance at that frequency, so a Q of 20 means the part’s loss is about 5 % of its reactance in that band.

    Self-resonance is quoted as 110 MHz minimum. Below it the part is inductive; above it the inter-layer capacitance takes over. The margin between the operating band and 110 MHz is the design headroom.

    Within the MCLA1608V1 family this is value 12 of 24, in a range that runs from 0.047 to 3.9 nH.

    Where This Series Fits

    The multilayer chip family covers nanohenry to a few microhenry values in 0402 through 1812 bodies. It is the range where the inductance is too small for a wound part to be practical and where the self-resonant frequency sets the usable band.

    • The rated current is a thermal limit for the part in free air, not a saturation limit. At high ambient the current has to be derated.
    • Typical applications: adas; infotainment; wireless communications; wifi, bluetooth, satellite; antenna tuning.
    • Design note: compare SRF against the highest frequency the circuit will see, not just the fundamental.

    Frequently Asked Questions

    How much does the value drift with temperature?
    The data sheet gives the tolerance band; the drift inside that band is small for this construction because there is no mechanical winding to move.

    Why is the inductance quoted at a test frequency?
    At nanohenry values the parasitic capacitance and the measurement fixture both matter. The value is only meaningful at the frequency stated, and the Q column tells you how much of the reactance is loss at that point.

    Can I replace a wire-wound chip with this part?
    Only if the Q and the current rating suit the circuit. Multilayer parts have lower Q and lower current capability than wire-wound parts of the same size.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products