Eaton MCLA1608V2-120-R 12.0 nH SMD Inductor, SRF 3000 MHz
Eaton MCLA1608V2-120-R 12.0 nH SMD Inductor, SRF 3000 MHz

Eaton MCLA1608V2-120-R 12.0 nH SMD Inductor, SRF 3000 MHz

Share
MCLA1608V2-120-R: multilayer chip inductor, 12.0 nH ±5%, Q 12, SRF 3000 MHz, 300 mA, DCR 450 mOhm.
    • Product Details
    • Download

    Eaton MCLA1608V2-120-R 12.0 nH SMD Inductor, SRF 3000 MHz

    MCLA1608V2-120-R at a glance: multilayer chip inductor, 12.0 nH ±5%, Q 12, SRF 3000 MHz, 300 mA, DCR 450 mOhm.

    Specification Table

    ParameterValue
    Orderable part numberMCLA1608V2-120-R
    Inductance12.0 nH ±5%
    Q minimum12
    DCR maximum @ +25 °C450 mOhm
    Rated current maximum300 mA
    SRF minimum3000 MHz
    Test frequency100 MHz
    Test voltage50 mV
    Package1.6 x 0.8 mm
    Size code1608 (0603)
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10976

    Mechanical Dimensions & Pad Layout

    Outline drawing and pad layout are on page 2 of Eaton Technical Data 10976; the package column above gives the body size in millimetres.

    What the Numbers Mean

    The inductance here is a few nanohenry, which puts the part in RF and high-speed digital territory: matching networks, filter sections, bias chokes on amplifier supplies, and the small isolation inductors that keep clock harmonics out of connectors. The multilayer body keeps the parasitics predictable, and the Q column tells you how much loss the part adds at the test frequency.

    The row reads 12.0 nH ±5% with a minimum Q of 12 at 100 MHz. Q is the ratio of reactance to resistance at that frequency, so a Q of 12 means the part’s loss is about 8.33 % of its reactance in that band.

    Self-resonance is quoted as 3000 MHz minimum. Below it the part is inductive; above it the inter-layer capacitance takes over. The margin between the operating band and 3000 MHz is the design headroom.

    Within the MCLA1608V2 family this is value 14 of 34, in a range that runs from 0.001 to 0.47 nH.

    What This Family Is For

    The multilayer chip family covers nanohenry to a few microhenry values in 0402 through 1812 bodies. It is the range where the inductance is too small for a wound part to be practical and where the self-resonant frequency sets the usable band.

    • The rated current is a thermal limit for the part in free air, not a saturation limit. At high ambient the current has to be derated.
    • Typical applications: adas; infotainment; wireless communications; wifi, bluetooth, satellite; antenna tuning.
    • Design note: compare SRF against the highest frequency the circuit will see, not just the fundamental.

    Frequently Asked Questions

    How much does the value drift with temperature?
    The data sheet gives the tolerance band; the drift inside that band is small for this construction because there is no mechanical winding to move.

    Can I replace a wire-wound chip with this part?
    Only if the Q and the current rating suit the circuit. Multilayer parts have lower Q and lower current capability than wire-wound parts of the same size.

    Why is the inductance quoted at a test frequency?
    At nanohenry values the parasitic capacitance and the measurement fixture both matter. The value is only meaningful at the frequency stated, and the Q column tells you how much of the reactance is loss at that point.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products