Eaton MCLA1608V2-2R7-R 2.7 nH SMD Inductor, SRF 6000 MHz
Eaton MCLA1608V2-2R7-R 2.7 nH SMD Inductor, SRF 6000 MHz

Eaton MCLA1608V2-2R7-R 2.7 nH SMD Inductor, SRF 6000 MHz

Share
MCLA1608V2-2R7-R: multilayer chip inductor, 2.7 nH ±0.3nH, Q 10, SRF 6000 MHz, 500 mA, DCR 120 mOhm.
    • Product Details
    • Download

    Eaton MCLA1608V2-2R7-R 2.7 nH SMD Inductor, SRF 6000 MHz

    MCLA1608V2-2R7-R at a glance: multilayer chip inductor, 2.7 nH ±0.3nH, Q 10, SRF 6000 MHz, 500 mA, DCR 120 mOhm.

    Electrical Specifications

    ParameterValue
    Orderable part numberMCLA1608V2-2R7-R
    Inductance2.7 nH ±0.3nH
    Q minimum10
    DCR maximum @ +25 °C120 mOhm
    Rated current maximum500 mA
    SRF minimum6000 MHz
    Test frequency100 MHz
    Test voltage50 mV
    Package1.6 x 0.8 mm
    Size code1608 (0603)
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10976

    Dimensions and Pad Layout

    Outline drawing and pad layout are on page 2 of Eaton Technical Data 10976; the package column above gives the body size in millimetres.

    Reading the Data Sheet

    This is a surface-mount multilayer inductor: printed coil, sintered body, silver terminations. The value is quoted at a defined test frequency because at these inductances the measurement conditions matter as much as the part.

    The row reads 2.7 nH ±0.3nH with a minimum Q of 10 at 100 MHz. Q is the ratio of reactance to resistance at that frequency, so a Q of 10 means the part’s loss is about 10 % of its reactance in that band.

    Self-resonance is quoted as 6000 MHz minimum. Below it the part is inductive; above it the inter-layer capacitance takes over. The margin between the operating band and 6000 MHz is the design headroom.

    Within the MCLA1608V2 family this is value 6 of 34, in a range that runs from 0.001 to 0.47 nH.

    What This Family Is For

    The multilayer chip family covers nanohenry to a few microhenry values in 0402 through 1812 bodies. It is the range where the inductance is too small for a wound part to be practical and where the self-resonant frequency sets the usable band.

    • The rated current is a thermal limit for the part in free air, not a saturation limit. At high ambient the current has to be derated.
    • Typical applications: adas; infotainment; wireless communications; wifi, bluetooth, satellite; antenna tuning.
    • Design note: compare SRF against the highest frequency the circuit will see, not just the fundamental.

    Frequently Asked Questions

    Why is the inductance quoted at a test frequency?
    At nanohenry values the parasitic capacitance and the measurement fixture both matter. The value is only meaningful at the frequency stated, and the Q column tells you how much of the reactance is loss at that point.

    Can I replace a wire-wound chip with this part?
    Only if the Q and the current rating suit the circuit. Multilayer parts have lower Q and lower current capability than wire-wound parts of the same size.

    What happens above the self-resonant frequency?
    The part becomes capacitive. Any filter or matching design has to keep the operating band below SRF, with margin for the tolerance of the value.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message